Dell Laptop M6600 Manual de usuario

Dell Precision M6600 Owner's ManualRegulatory Model P10ERegulatory Type P10E001

NOTE: The color of your computer and certain components may appear differentlythan shown in this document.To avoid damaging your computer, perform the

100

Camera 33Removing The Camera1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the standard display bezel or t

Installing The Camera1. Place the camera and microphone module on the display cover and tightenthe screw securing the camera and microphone module in

Display Hinge Cap Tower 34Removing The Display Hinge Cap Tower1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remo

15. Remove the display hinges.16. Release the display hinge towers from the cables and remove the hingetowers.104

Installing The Display Hinge Cap Tower1. Insert the display hinge towers with the open end facing inward and ensurethe cables and antennas are not pin

106

Low-Voltage Differential Signaling(LVDS) Camera Cable 35Removing The Low-Voltage Differential Signaling (LVDS) Camera Cable1. Follow the procedures in

16. Remove the LVDS cable from the routing channel.17. Remove the LVDS cable.108

Installing The Low-Voltage Differential Signaling (LVDS) Camera Cable1. Secure the low-voltage differential signaling (LVDS) cable to its routingchann

• #0 Phillips screwdriver• #1 Phillips screwdriver• Small plastic scribe• Flash BIOS update program CDTurning Off Your ComputerCAUTION: To avoid losin

110

Specifications 36Technical SpecificationsNOTE: Offerings may vary by region. For more information regarding theconfiguration of your computer, click S

VideoType discreteData bus integrated videoVideo controller andmemory:M4600• AMD FirePro M5950 Mobility Pro Graphics with 1 GBGDDR5• NVIDIA Quadro 100

System InformationInterrupt Levels Integrated I/O APIC capability with 24interruptsBIOS Chip (NVRAM) 8 Mb (256 KB)Expansion BusBus Type PCI 2.3, PCI E

Battery365 g (0.80 lb) (6–cell)500 g (1.10 lb) (9–cell / 9–cell LCL)Voltage 11.10 VTemperature range:Operating 0 °C to 35 °C (32 °F to 95 °F)Non-opera

Contactless Smart CardISO15693HID iClassFIPS201NXP DesfirePhysical M4600 M6600Height 36.5 mm (1.44 inches) 37.20 mm (1.46 inches)Width 376 mm (14.80 i

EnvironmentalAirborne contaminant level G1 or lower as defined by ANSI/ISA-S71.04-1985116

System Setup 37System Setup OverviewSystem Setup allows you to:• change the system configuration information after you add, change, orremove any hardw

Option DescriptionSystem Information This section lists the primary hardwarefeatures of your computer.• System Information• Memory Information• Proces

• Disabled• Enabled• Enabled w/PXEDefault Setting: Enabled w/PXESystem Management Allows you to control the systemsmanagement mechanism. The options a

CAUTION: To connect a network cable, first plug the cable into the network deviceand then plug it into the computer.3. Replace the battery.4. Connect

NOTE: SATA is configured to supportRAID mode.USB Controller Allows you to control the USB controller.The options are:• Enable Boot Support• Enable Ext

• SATA-1• SATA-4• SATA-5Default Setting: All drives are enabled.VideoThe following table describe the menu options of the Video menu.Option Descriptio

NOTE: Successful password changestake effect immediately.Default Setting: Not setInternal HDD-0 Password Allows you to set or change the system's

Computrace Allows you to activate or disable theoptional Computrace software The optionsare:• Deactivate• Disable• ActivateNOTE: The Activate and Disa

• 2Default Setting: AllIntel SpeedStep Allows you to enable or disable the IntelSpeedStep feature.Default Setting: EnabledC-States Control Allows you

Default Setting: DisabledUSB Wake Support Allows you to enable USB devices to wakethe system from Standby.Default Setting: DisabledNOTE: This feature

ExpressCharge Allows you to enable or disable theExpressCharge feature. The options are:• Standard• ExpressChargeDefault Setting: ExpressChargePOST Be

Default Setting: Enable Fn Key Emulation isselected.POST HotKeys Allows you to enable the sign-on screenmessage display indicating the keystrokesequen

Option DescriptionWireless Switch Allows you to set the wireless devices thatcan be controlled by the wireless switch.The options are:• WWAN• WLAB• Bl

Power Events Allows you to view and clear the Powerevents.129

Secure Digital (SD) Card 2Removing The Secure Digital (SD) Card1. Follow the procedures in Before Working On Your Computer2. Press in the Secure Digit

130

Diagnostics 38Device Status LightsTurns on when you turn on the computer and blinks when the computer is in apower management mode.Turns on when the c

Device Status LightsTurns on when you turn on the computerand blinks when the computer is in apower management mode.Turns on when the computer reads o

Diagnostic LED Error DescriptionBlinkingSolid Solid The microcontroller is handing control ofthe system to the processor. This codepersists if no proc

134

Contacting Dell 39Contacting DellTo contact Dell for sales, technical support, or customer service issues:1. Visit support.dell.com.2. Verify your cou

14

ExpressCard 3Removing the ExpressCard1. Follow the procedures in Before Working On Your Computer.2. Press in on the ExpressCard gently to release it f

16

Battery 4Removing The Battery1. Follow the procedures in Before Working On Your Computer.2. Slide the battery release latch into the unlock position.3

18

Subscriber Identity Module (SIM)Card 5Removing The Subscriber Identity Module (SIM )Card1. Follow the procedures in Before Working On Your Computer.2.

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of yourcomputer.CAUTION: A CAUTION indicates

Installing The Subscriber Identity Module (SIM )Card1. Locate the Subscriber Identity Module (SIM) card slot in the batterycompartment.2. Push the SIM

Bluetooth Card 6Removing The Bluetooth Card1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Slide the Bluetooth doo

6. Remove the Bluetooth card.Installing The Bluetooth Card1. Place the Bluetooth card on the Bluetooth door and align with the screwhole.2. Tighten th

Base Cover 7Removing The Base Cover1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the screws that secure

Installing The Base Cover1. Slide the bottom door downwards and towards the front of the computer.2. Tighten the screws that secure the base cover to

Keyboard Trim 8Removing The Keyboard Trim1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Using a plastic scribe,

Installing The Keyboard Trim1. Align the keyboard trim with the tabs on the top of the palm rest.2. Press downwards along the bottom edge to latch on

Keyboard 9Removing The Keyboard1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the keyboard trim.4. Remove

7. Remove the keyboard.8. Peel back the adhesive tape securing the keyboard data cable to the backof the keyboard.9. Disconnect the keyboard data cabl

10. Peel the keyboard data cable away from the keyboard and remove.Installing The Keyboard1. Connect the keyboard data cable to the back of the keyboa

ContentsNotes, Cautions, and Warnings...21 Working on Your Computer...

30

Optical Drive 10Removing The Optical Drive1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover.4

7. Remove the optical drive bracket from the drive.Installing The Optical Drive1. Tighten the screws to secure the bracket to the back of the optical

Primary Hard Drive 11Removing The Primary Hard Drive1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the ba

7. Remove the hard drive bracket from the computer.8. Flex the hard drive bracket outward and press the hard drive upwards fromthe bottom.9. Remove th

Installing The Primary Hard Drive1. Align the hard drive to the hard drive bracket.2. Slide the hard drive into the hard drive bracket.3. Slide the ha

36

Secondary Hard Drive 12Removing The Secondary Hard Drive1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove th

7. Remove the hard drive bracket from the hard drive.Installing The Secondary Hard Drive1. Attach the hard drive bracket to the hard drive.2. Tighten

Wireless Local Area Network(WLAN) Card 13Removing Wireless Local Area Network (WLAN) Card1. Follow the procedures in Before Working On Your Computer.2

Installing The Base Cover...248 Keyboard Trim...

Installing The Wireless Local Area Network (WLAN) Card1. Slide the WLAN card into its slot.2. Tighten the screw securing the WLAN card in place.3. Con

Wireless Wide Area Network(WWAN) Card 14Removing The Wireless Wide Area Network (WWAN) Card1. Follow the procedures in Before Working On Your Computer

Installing The Wireless Wide Area Network (WWAN) Card1. Slide the Wireless Wide Area Network (WWAN) card into its slot.2. Tighten the screw securing t

Primary Memory 15Removing The Primary Memory1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.

Installing The Primary Memory1. Locate the memory slot in the computer.2. Insert the memory into the memory socket.3. Press down on the memory until t

Secondary Memory 16Removing The Secondary Memory1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the keyboar

8. Remove the memory module from the computer.Installing The Secondary Memory1. Locate the memory slot in the computer.2. Insert the memory into the m

CPU Fan 17Removing The CPU Fan1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4. Disconnect

Installing The CPU Fan1. Locate the CPU fan compartment in the computer.2. Tighten the screws securing the CPU fan in place.3. Connect the CPU fan cab

Coin-Cell Battery 18Removing The Coin-Cell Battery1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base

16 Secondary Memory...45Removing The Secondary Memory...

Installing The Coin-Cell Battery1. Attach the coin-cell battery to the coin-cell compartment.2. Connect the coin-cell battery to the system board.3. I

Palm Rest 19Removing The Palm Rest1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4. Remove

11. Loosen the captive screws.12. Disconnect the speaker cable.13. Disconnect the media board cable.52

14. Disconnect the touchpad cable.15. Disconnect the Radio Frequency Identification (RFID) cable.16. Disconnect the fingerprint reader cable.53

17. Disconnect the Bluetooth cable.18. Disconnect the power button cable.19. Lift up the left edge of palm rest assembly.54

20. Release the tabs along the edges of the palmrest.21. Disconnect the Bluetooth cable from the Bluetooth module.22. Remove the palm rest.55

Installing The Palm Rest1. Align the metal anchors at the bottom edge of the palm rest to the anchorhooks on the computer.2. Starting from the right e

CPU and Heatsink 20Removing The CPU Heatsink1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.

13. Lift up the CPU heatsink and remove from the computer.Installing The CPU Heatsink1. Locate the heatsink compartment on the computer.2. Tighten the

Processor 21Removing The Processor1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4. Remove

Installing The ExpressCard Module...6825 Input/Output Board...

Installing The Processor1. Insert the processor into the processor socket. Ensure that the processor isproperly seated.2. Tighten the cam lock in a cl

Graphics Card Heatsink 22Removing The Graphics Card Heatsink1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove

14. Pull the antennas through the opening to the top of the computer.15. Disconnect the graphics card fan cable.16. Remove the screw securing the grap

17. Loosen the captive screws (1 > 2 > 3 > 4) on the heatsink.18. Lift up the graphics card heatsink and remove from the computer.63

Installing The Graphics Card Heatsink1. Locate the heatsink compartment on the computer.2. Tighten the captive screws (1 > 2 > 3). Ensure the he

Graphics Card 23Removing The Graphics Card1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4.

Installing The Graphics Card1. Locate the graphics card slot on the computer.2. Tighten the screws securing the graphics card in place.3. Install the

ExpressCard Module 24Removing The ExpressCard Module1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the bas

12. Remove the ExpressCard module.Installing The ExpressCard Module1. Place the ExpressCard module in the computer and tighten the screwssecuring the

Input/Output Board 25Removing The Input/Output Board1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the bas

33 Camera...101Removing The Camera...

12. Lift the right edge of the IO board upwards to disengage the connector andremove from the computer.70

Installing The Input/Output Board1. Place the Input/Output (IO) board on the computer and ensure theconnector is properly engaged to the matching conn

72

DC-in Jack 26Removing The DC-in Jack1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4. Remov

15. Remove the DC-in bracket.16. Remove the DC-in jack.74

Installing The DC-in Jack1. Place the DC-in jack in the computer.2. Place the DC-in bracket in the system and tighten the single screwsecuring it in p

76

Display Assembly 27Removing The Display Assembly1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base co

12. Remove the screws at the bottom of the computer.13. Remove the screws at the rear of the computer.14. Pull the antennas through the opening to the

15. Loosen the captive screws securing the low-voltage differential signaling(LVDS) cable in place.16. Disconnect the LVDS cable.17. Disconnect the ca

8

18. Remove the screws securing the display assembly in place.19. Remove the display assembly.80

Installing The Display Assembly1. Attach the display assembly to the base of the computer.2. Tighten the screws on the display assembly securing it in

82

System Board 28Removing The System Board1. Follow the procedures in Before Working On Your Computer2. Remove the Secure Digital (SD) Card3. Remove the

23. Disconnect the wireless switch cable on the top side of the system board.24. Disconnect the DC-in cable.25. Remove the screws securing the system

26. Gently lift the bottom edge of the system board assembly and raise it to a 45degree angle.27. Release the system board from the port connectors on

Installing The System Board1. Align the system board to the port connectors on the rear of the chassisand place the system board in the computer.2. Ti

Touchscreen Display Bezel 29Removing The Touchscreen Display Bezel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3.

6. Pry up the right edge of the display bezel.7. Pry up the bottom edge of the display bezel.8. Work your way around the left edge of the display beze

9. Remove the display bezel.Installing The Touchscreen Display Bezel1. Place the display bezel on the computer.2. Starting from the bottom edge, press

Working on Your Computer 1Before Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potentialdamage an

90

Touchscreen Display Panel 30Removing The Touchscreen Display Panel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3.

7. Peel back the adhesives and disconnect the low-voltage differentialsignaling (LVDS) cable from the back of the display panel.8. Disconnect the digi

10. Remove the touchscreen display panel.11. Remove the screws securing the display bracket to the display panel.12. Remove the display bracket.93

Installing The Touchscreen Display Panel1. Align the display bracket with the display panel and tighten the four screwssecuring the display bracket in

Display Bezel 31Removing The Display Bezel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Carefully pry up the to

Installing The Display Bezel1. Place the display bezel on the computer.2. Starting from the bottom edge, press downward on the display bezel toengage

Display Panel 32Removing The Display Panel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the display beze

7. Peel back the adhesives and disconnect the low-voltage differentialsignaling (LVDS) cable from the back of the display panel.8. Remove the display

10. Remove the display bracket.Installing The Display Panel1. Align the display bracket with the display panel and tighten the screwssecuring the disp