Dell OpenManage Server Administrator Version 6.3 Manual de usuario

Dell OpenManageServer AdministratorVersion 6.3Command Line Interface User’s Guidetitle.fm Page 1 Friday, July 16, 2010 3:56 PM

10 Contentsomreport Fan Status . . . . . . . . . . . . . . . . 179omreport Power Supply Status. . . . . . . . . . . 180omreport EMM Status . . . .

100 omconfig: Managing Components Using the Instrumentation Serviceattribute=romb setting=raid | off | scsiforce=trueraid: Instructs the BIOS to detec

omconfig: Managing Components Using the Instrumentation Service 101attribute=secondaryscsisetting=on | off on: Enables this device.off: Disables this

102 omconfig: Managing Components Using the Instrumentation Serviceattribute=serialport1setting=off | auto | com1 | com3 | bmcserial | bmcnic | rac |

omconfig: Managing Components Using the Instrumentation Service 103attribute=uausb setting=on | backonly | offon: Enables the user-accessible USB port

104 omconfig: Managing Components Using the Instrumentation Serviceomconfig chassis currents/omconfig mainsystem currents NOTE: This command is no lo

omconfig: Managing Components Using the Instrumentation Service 105Specifying a Value for Minimum and Maximum Warning ThresholdsIf you prefer to speci

106 omconfig: Managing Components Using the Instrumentation Service• Ambient temperature of the system• Remote access IPv4 address• Remote access IPv6

omconfig: Managing Components Using the Instrumentation Service 107 NOTE: The options ipv4idrac, ipv6idrac, and macidrac are deprecated.omconfig chas

108 omconfig: Managing Components Using the Instrumentation ServiceIndex 0 always defaults to the main system chassis. The following command omits ind

omconfig: Managing Components Using the Instrumentation Service 109omconfig chassis memorymode/omconfig mainsystem memorymodeUse the omconfig chassis

Contents 11omconfig Stop Patrol Read . . . . . . . . . . . . 205omconfig Change Controller Properties. . . . . . 206omconfig Storage Virtual Disk .

110 omconfig: Managing Components Using the Instrumentation Serviceomconfig chassis pwrmanagement/omconfig mainsystem pwrmanagementUse the omconfig ch

omconfig: Managing Components Using the Instrumentation Service 111Table 4-9. omconfig chassis pwrmanagement/omconfig mainsystem pwrmanagementname=val

112 omconfig: Managing Components Using the Instrumentation Service NOTE: Reboot your system for the power profiles setup options to take effect.omco

omconfig: Managing Components Using the Instrumentation Service 113 NOTE: This command is applicable to select Dell xx0xsystems that support PMBus on

114 omconfig: Managing Components Using the Instrumentation ServiceSpecify a Value for Warning ThresholdsIf you prefer to specify values for the power

omconfig: Managing Components Using the Instrumentation Service 115The output of the omconfig chassis remoteaccess or omconfig mainsystem remoteaccess

116 omconfig: Managing Components Using the Instrumentation Servicealtdnsserverv6 Validates the address of the alternate DNS server for configuration.

omconfig: Managing Components Using the Instrumentation Service 117ipsource=static | dhcp | systemsoftwarestatic: Static if the IP address of the BMC

118 omconfig: Managing Components Using the Instrumentation Servicevlanid=number number: Virtual LAN identification in the range of 1 to 4094.vlanprio

omconfig: Managing Components Using the Instrumentation Service 119config=serial (continued)mode=directbasic | directterminal | directbasicterminal |

12 Contentsomconfig Offline Physical Disk . . . . . . . . . . . 227omconfig Offline Physical Disk. . . . . . . . . . . 227omconfig Online Physical D

120 omconfig: Managing Components Using the Instrumentation Serviceconfig=serialoverlan enable=true | false true: Enables serial over LAN for the BMC.

omconfig: Managing Components Using the Instrumentation Service 121privilegelevel=administrator | operator | useradministrator: Sets the maximum privi

122 omconfig: Managing Components Using the Instrumentation Servicenewlinesequence=none | crlf | null | cr | lfcr | lfnone: BMC does not use a termina

omconfig: Managing Components Using the Instrumentation Service 123id=number newpw=text confirmnewpw=textnumber: ID (in numeric format) of the user be

124 omconfig: Managing Components Using the Instrumentation Serviceid=user id dracusergroup=admin | poweruser | guest | custom | noneid=user id: User

omconfig: Managing Components Using the Instrumentation Service 125Table 4-12. omconfig chassis remoteaccess config=user id=<user id> dracusergr

126 omconfig: Managing Components Using the Instrumentation Serviceomconfig chassis temps/omconfig mainsystem tempsUse the omconfig chassis temps or o

omconfig: Managing Components Using the Instrumentation Service 127Specify a Value for Minimum and Maximum Warning ThresholdsIf you want to specify va

128 omconfig: Managing Components Using the Instrumentation ServiceDefault Minimum and Maximum Warning Threshold ValuesIf you want to set both the upp

omconfig: Managing Components Using the Instrumentation Service 129 NOTE: Minimum and maximum warning threshold values for the voltage cannot be set

Contents 137 Working With CLI Command Results . . . . . . . . . . . . . . . . . . . . . . . . . 251Output Options for Command Results . . . . . . .

130 omconfig: Managing Components Using the Instrumentation Serviceomconfig preferences snmpSetting the SNMP root password allows administrators to re

omconfig: Managing Components Using the Instrumentation Service 131When you type omconfig preferences snmp setting=rootpw, the system prompts you to s

132 omconfig: Managing Components Using the Instrumentation Serviceomconfig preferences useraccessDepending on the policies of your organization, you

omconfig: Managing Components Using the Instrumentation Service 133Table 4-20. Configuring Webserver PreferencesFor example, to set the URL launch poi

134 omconfig: Managing Components Using the Instrumentation Serviceomconfig system/omconfig servermoduleUse the omconfig system or omconfig servermodu

omconfig: Managing Components Using the Instrumentation Service 135The event is a power supply failure and the action is to broadcast a message to all

136 omconfig: Managing Components Using the Instrumentation Serviceevent=fanwarn Sets actions when a fan probe detects a warning value.event=fanfail S

omconfig: Managing Components Using the Instrumentation Service 137 NOTE: storagectrlbatterywarn and storagectrlbatteryfail events are not available

138 omconfig: Managing Components Using the Instrumentation ServiceExample Current Probe ActionsTo disable system console alert if a current probe det

omconfig: Managing Components Using the Instrumentation Service 139Commands for Clearing Logs NOTE: For more information about alert messages, see th

14 Contents

140 omconfig: Managing Components Using the Instrumentation Serviceomconfig system platformevents/omconfig servermodule platformeventsUse the omconfig

omconfig: Managing Components Using the Instrumentation Service 141Table 4-25 lists the components and the events for which you can set platform event

142 omconfig: Managing Components Using the Instrumentation Serviceevent=intrusion Sets action or enables/disables alert generation when a chassis is

omconfig: Managing Components Using the Instrumentation Service 143omconfig system events/omconfig servermodule eventsUse the omconfig system events o

144 omconfig: Managing Components Using the Instrumentation Serviceomconfig system events source=snmptrapsoromconfig servermodule events source=snmptr

omconfig: Managing Components Using the Instrumentation Service 145IndexIndex refers to the number of an event for a particular component. Index is an

146 omconfig: Managing Components Using the Instrumentation Serviceomconfig system events type=fan index=0 severity=criticaloromconfig servermodule ev

omconfig: Managing Components Using the Instrumentation Service 147Example Recovery CommandsTo set the action on hung operating system detection to po

148 omconfig: Managing Components Using the Instrumentation ServiceExample Shutdown CommandsTo set the shutdown action to reboot, type:omconfig system

omconfig: Managing Components Using the Instrumentation Service 149Table 4-31 shows the valid parameters for the command.Example Thermal Shutdown Comm

Introduction 151IntroductionYou can perform essential systems management tasks using Dell OpenManage Server Administrator’s graphical user interface (

150 omconfig: Managing Components Using the Instrumentation Service

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 1515omconfig system or servermodule assetinfo: Editing Cost of Ownership V

152 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesAdding Acquisition InformationAcquisition refers to the facts about a b

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 153Example Commands for Adding Acquisition InformationTo provide a value f

154 omconfig system or servermodule assetinfo: Editing Cost of Ownership Valuesyes costcenter=financeoromconfig servermodule assetinfo info=acquisitio

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 155Example Commands for Adding Depreciation InformationTo provide a value

156 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesTable 5-4 shows the valid parameters for the command.Example Command fo

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 157You can type more than one omconfig system assetinfo or omconfig server

158 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesExample Command for Adding Lease InformationTo provide a value for a le

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 159Example Command for Adding Maintenance InformationTo provide a value fo

16 Introduction NOTE: For information on terms used in this document, see the Glossary on the Dell support website.What's New in Version 6.3Foll

160 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesAdding Outsource InformationOutsourcing is the practice of contracting

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 161Example Command for Adding Outsource InformationTo provide a value for

162 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesExample Command for Adding Owner InformationTo provide a value for an o

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 163Example Command for Adding Service InformationTo provide a value for a

164 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesYou can type more than one omconfig system assetinfo or omconfig server

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 165Example Command for Adding Support InformationTo provide a value for a

166 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesAdding System InformationSystem information includes the primary user o

omconfig system or servermodule assetinfo: Editing Cost of Ownership Values 167You can type more than one omconfig system assetinfo or omconfig server

168 omconfig system or servermodule assetinfo: Editing Cost of Ownership ValuesExample Command for Adding Warranty InformationTo provide a value for a

Using the Storage Management Service 1696Using the Storage Management ServiceThe CLI of Storage Management enables you to perform all of Storage Manag

Introduction 17•omconfig•omhelp•omreportThe omconfig command writes values that you assign to an object's properties. You can specify values for

170 Using the Storage Management ServiceTable 6-1 describes these command levels.Following the command levels, the omreport and omconfig command synta

Using the Storage Management Service 171Table 6-2. Syntax For Name=Value Pairs For ParametersSyntax Description controller=id Indicates the controller

172 Using the Storage Management ServiceUser Privileges for omreport storage and omconfig storageStorage Management requires Administrator privileges

Using the Storage Management Service 173omreport Storage Help Table 6-3 provides the omreport storage command syntax.Table 6-3. omreport storage helpC

174 Using the Storage Management Serviceomreport Controller StatusTable 6-4 describes the syntax for the omreport Controller Commands.omreport Global

Using the Storage Management Service 175omreport Battery StatusTable 6-6 describes the syntax for the omreport Battery Commands.omreport Connector Sta

176 Using the Storage Management Serviceomreport Enclosure Status Table 6-8 describes the syntax for the omreport Enclosure Commands.Table 6-7. omrepo

Using the Storage Management Service 177controller=id enclosure=<ENCLOSUREID> where id is the controller number and <ENCLOSUREID> is the e

178 Using the Storage Management Serviceomreport Temperature Probe StatusTable 6-9 describes the syntax for the omreport Probe CommandsTable 6-9. omre

Using the Storage Management Service 179omreport Fan StatusTable 6-10 describes the syntax for the omreport Fan CommandsTable 6-10. omreport Fan Statu

18 Introduction NOTE: omupdate commands are no longer supported in Server Administrator and are replaced by Dell Update Package or Server Update Util

180 Using the Storage Management Serviceomreport Power Supply StatusTable 6-11 describes the syntax for the omreport Power Supply CommandsTable 6-11.

Using the Storage Management Service 181omreport EMM Status NOTE: The status of the EMMs is displayed as degraded if there is a mismatch between the

182 Using the Storage Management Serviceomreport Enclosure Slot Occupancy ReportTable 6-13 describes the syntax for the omreport Enclosure Slot Occupa

Using the Storage Management Service 183omreport Physical Disk Status Table 6-14 describes the syntax for the omreport Physical Disk CommandsTable 6-1

184 Using the Storage Management Serviceomreport Virtual Disk Status Table 6-15 describes the syntax for the omreport Virtual Disk Commandsomconfig Gl

Using the Storage Management Service 185omconfig Global Enable Smart Thermal ShutdownBy default, the operating system and server shut down when the PV

186 Using the Storage Management ServiceComplete Syntaxomconfig storage globalinfo action=disablestsExample SyntaxThe omconfig command syntax for disa

Using the Storage Management Service 187Complete SyntaxFor dedicated hot spare protection policy, type:omconfig storage globalinfo action=setprotectio

188 Using the Storage Management ServiceTable 6-17. omconfig Controller CommandsRequired Command Levels (1, 2, 3) Optional name=value pairs omconfig s

Using the Storage Management Service 189action=setbgirate controller=id rate=<0 to 100 >action=setreconstructrate controller=idrate=<0 to 100

Introduction 19omconfig system assetinfo info=depreciation duration=6Message:Asset information set successfully.Failure MessagesCLI failure messages p

190 Using the Storage Management Serviceomconfig Rescan Controller Use the following omconfig command syntax to rescan a controller. See Dell OpenMana

Using the Storage Management Service 191omconfig Disable Controller Alarm Use the following omconfig command syntax to disable the controller alarm. S

192 Using the Storage Management Serviceomconfig Test Controller Alarm Use the following omconfig command syntax to test the functionality of the cont

Using the Storage Management Service 193omconfig storage controller action=resetconfig controller=id force=yesExample Syntax To reset the configuratio

194 Using the Storage Management ServiceComplete Syntax omconfig storage controller action=createvdisk controller=id raid=<c| r0| r1| r1c| r5| r6|

Using the Storage Management Service 195raid=<c| r0| r1| r1c| r5| r6| r10| r50| r60> Parameter (Required) Use the raid=<c| r0| r1| r1c| r5| r

196 Using the Storage Management Servicesize=<number | max | min> Parameter (Required) Table 6-19 indicates how to specify the size=<number |

Using the Storage Management Service 197[cachepolicy=<d | c>] Parameter (Optional) Different controllers support different cache policies. Table

198 Using the Storage Management Service[writepolicy=<wb| wt| wc| nwc>] Parameter (Optional) Different controllers support different write polic

Using the Storage Management Service 199Example Syntax For example, you may want to create a RAID-5 virtual disk on a PERC 3/QC controller. See the De

Notes and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potenti

20 IntroductionMessage:Voltage probe warning threshold(s) set successfully.Scripting and Comparing With the CLIThe Server Administrator CLI allows adm

200 Using the Storage Management ServiceExample Syntax To set the rebuild rate to 50 on controller 1, type: omconfig storage controller action=setrebu

Using the Storage Management Service 201Example SyntaxTo set the reconstruct rate to 50 on controller 1, type:omconfig storage controller action=setre

202 Using the Storage Management ServiceExample Syntax To export the log on controller 1, type: omconfig storage controller action=exportlog controlle

Using the Storage Management Service 203Complete Syntax omconfig storage controller action=importrecoverforeignconfig controller=id where id is the co

204 Using the Storage Management ServiceComplete Syntaxomconfig storage controller action=setpdiskpwrmanagement spindownunconfigureddrives=<enabled

Using the Storage Management Service 205omconfig Start Patrol ReadUse the following omconfig command syntax to start the patrol read task on the contr

206 Using the Storage Management Serviceomconfig Change Controller PropertiesUse the following omconfig command to change any or all of the following

Using the Storage Management Service 207Example Syntax To replace physical disk (PD1) with another physical disk (PD2), type: omconfig storage vdisk a

208 Using the Storage Management Serviceomconfig Virtual Disk Commands The following sections provide the omconfig command syntax required to execute

Using the Storage Management Service 209omconfig Blink Virtual Disk Use the following omconfig command syntax to blink the physical disks included in

Introduction 21system usage. Command results can be routed to a file for later analysis. Reports can help administrators gain information that can be

210 Using the Storage Management Servicewhere id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values,

Using the Storage Management Service 211where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values,

212 Using the Storage Management Serviceomconfig Slow Initialize Virtualize DiskUse the following omconfig command syntax to slow initialize a virtual

Using the Storage Management Service 213where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values,

214 Using the Storage Management ServiceComplete Syntax omconfig storage vdisk action=splitmirror controller=id vdisk=id where id is the controller ID

Using the Storage Management Service 215omconfig Assign Dedicated Hot SpareUse the following omconfig command syntax to assign one or more physical di

216 Using the Storage Management Serviceomconfig Unassign Dedicated Hot SpareUse the following omconfig command syntax to unassign one or more physica

Using the Storage Management Service 217omconfig Check Consistency Use the following omconfig command syntax to initiate a check consistency on a virt

218 Using the Storage Management Serviceomconfig Pause Check Consistency Use the following omconfig command syntax to pause a check consistency while

Using the Storage Management Service 219omconfig Delete Virtual Disk Use the following omconfig command syntax to delete a virtual disk. CAUTION: De

22 Introductionomconfig system assetinfo info=acquisitionpurchasecost=<n> waybill=<n> installdate=<mmddyy> purchasedate=<mmddyy&g

220 Using the Storage Management Servicewhere id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values,

Using the Storage Management Service 221omconfig storage vdisk action=reconfigure controller=1 vdisk=4 raid=r5 pdisk=0:2:0,0:2:1,0:2:2,0:2:3 Example S

222 Using the Storage Management Service•[writepolicy=<wb| wt| wc| nwc | fwb>] Parameter (Optional)•[cachepolicy=<d | c>] Parameter (Optio

Using the Storage Management Service 223where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain the values fo

224 Using the Storage Management Serviceomconfig Blink Physical Disk You can blink the light (light emitting diode or LED display) on one or more phys

Using the Storage Management Service 225omconfig Unblink Physical Disk You can unblink the light (light emitting diode or LED display) on one or more

226 Using the Storage Management Servicewhere id is the controller ID. The <PDISK> variable specifies the physical disk. To obtain these values,

Using the Storage Management Service 227Example Syntax In this example, you want to initialize physical disk 3 on connector 0 of controller 1. On a SA

228 Using the Storage Management ServiceComplete Syntax omconfig storage pdisk action=offline controller=id pdisk=<PDISKID>where id is the contr

Using the Storage Management Service 229Example Syntax In this example, you want to bring physical disk 3 on connector 0 of controller 1 back online.

Using the omhelp Command 232Using the omhelp CommandThe omhelp command and its equivalent, <command> -?, accesses the CLI's detailed help t

230 Using the Storage Management Serviceomconfig storage pdisk action=assignglobalhotspare controller=1 pdisk=0:3 assign=yes Example for SAS Controlle

Using the Storage Management Service 231Example for SAS Controllers To unassign the physical disk described in this example as a global hot spare, typ

232 Using the Storage Management Serviceomconfig Cancel Rebuild Physical DiskUse the following omconfig command syntax to cancel a rebuild that is in

Using the Storage Management Service 233Complete Syntax omconfig storage pdisk action=removedeadsegments controller=id pdisk=<PDISKID> where id

234 Using the Storage Management ServiceTo obtain these values, type omreport storage controller to display the controller IDs and then type omreport

Using the Storage Management Service 235omconfig Cancel Replace MemberUse the following omconfig command syntax to cancel a replace member operation.

236 Using the Storage Management ServiceComplete Syntax omconfig storage battery action=recondition controller=id battery=id where id is the controlle

Using the Storage Management Service 237Complete Syntaxomconfig storage battery action=delaylearn controller=id battery=iddays=d hours=hwhere id is th

238 Using the Storage Management Servicewhere id is the controller ID and the connector ID as reported by the omreport command. To obtain these values

Using the Storage Management Service 239action=resetalltempprobes controller=idenclosure=<ENCLOSUREID>action=blink controller=idenclosure=<EN

24 Using the omhelp Command• shutdown• thrmshutdown• webserverFigure 2-1 shows the levels of help for a command.Figure 2-1. Different Levels of Help f

240 Using the Storage Management Serviceomconfig Enable Enclosure Alarm Use the following omconfig command syntax to enable the enclosure alarm: Compl

Using the Storage Management Service 241Example for SCSI, SATA, and ATA Controllers To disable the alarm on the enclosure attached to connector 2 on c

242 Using the Storage Management Serviceomconfig Set Enclosure Asset Name Use the following omconfig command syntax to specify the asset name for an e

Using the Storage Management Service 243where id is the controller ID and the temperature probe ID. The <ENCLOSUREID> variable specifies the enc

244 Using the Storage Management ServiceExample for SCSI, SATA, and ATA Controllers In this example, temperature probe 3 resides in the enclosure atta

Using the Storage Management Service 245omconfig Reset All Temperature Probe ThresholdsUse the following omconfig command syntax to reset the minimum

246 Using the Storage Management ServiceExample for SCSI, SATA, and ATA Controllers To blink the LEDs for the enclosure attached to connector 2 on con

Using the Storage Management Service 247

248 Using the Storage Management Service

Using the Storage Management Service 249

Using the omhelp Command 25For one info value, specify one or more optional parameter(s). Table 2-1 displays the optional parameters for info=acquisit

250 Using the Storage Management Service

Working With CLI Command Results 2517Working With CLI Command ResultsServer Administrator Command Line Interface (CLI) users can use the command outpu

252 Working With CLI Command ResultsLinux Enterprise Server terminal. To display command output with control over scrolling, type the CLI command and

Working With CLI Command Results 253Four hours later, you repeat the command. You have no interest in the 11:00 A.M. snapshot as written to fans.txt.

254 Working With CLI Command ResultsFans.txt now reads as follows:You can use a text editor to insert the time that each block of data was captured. I

Working With CLI Command Results 255The available formats include: •List (lst)• Semicolon-separated values (ssv)•Table (tbl)•Raw XML (xml)• Custom del

256 Working With CLI Command ResultsNo special formatting option is required because list format is the default display format. The network data part

Working With CLI Command Results 257Semicolon-separated Values (ssv)Use the ssv formatting option to deliver output formatted in semicolon-separated v

258 Working With CLI Command ResultsCustom Delimited Format (cdv)Use the cdv formatting option to report exported data in custom delimited format. You

Index 259IndexSymbols-?omconfig, 86omconfig chassis, 89omreport, 35request for help, 23Aaboutomconfig, 87acquisitioninformation, 152optional parameter

26 Using the omhelp Command

260 Indexbiosomreport chassis, 39biossetupomconfig chassis, 89omreport chassis, 39blinkomconfig, 245blink physical diskomconfig, 224bmcomconfig chassi

Index 261Windows command prompt, 16cmdlogomconfig system, 139omreport system, 62command levels 1,2, and 3omconfig, 81command levels 1,2,3omreport, 29c

262 Indexdefault maximum warning threshold, 104default minimum warning threshold, 104defining alert actions, 134delay battery learn cycleomconfig, 236

Index 263omreport chassis, 44firmwareomreport chassis, 45format virtual disk, 219formatting CLI command output, 254frontpanelomconfig chassis, 105omre

264 Indexminimum warning threshold, 127Nname=value pairsomconfig chassis biossetup, 89omconfig chassis bmc, 115nicsomreport chassis, 50NMI button, 45O

Index 265set enclosure asset name, 242set enclosure asset tag, 241set temperature probe thresholds, 242split mirror, 213system, 134test controller ala

266 Indexdirservice, 129snmp, 130-131useraccess, 132webserver, 132omconfig preferences dirservicename=value pair, parameters, 130omconfig preferences

Index 267about, 36battery status, 175chassis, 37command levels 1, 2, 3, 29command summary, 28connector status, 175controller status, 174EMM status, 18

268 Indexenclosure, 176, 178-182globalinfo, 175pdisk, 183vdisk, 184omreport systemalertaction, 63alertlog, 62assetinfo, 65cmdlog, 62esmlog, 62events,

Index 269processorsomreport chassis, 51pwrmanagement, 55pwrsuppliesomreport chassis, 58Rread policy parameters, 197rebuild physical diskomconfig, 231r

omreport: Viewing System Status Using the Instrumentation Service 273omreport: Viewing System Status Using the Instrumentation ServiceThe omreport com

270 Indexsmart thermal shutdown status, 174snmpomconfig preferences, 130SNMP traps, 143disabling, 143enabling, 143split mirroromconfig, 213start batte

Index 271Vvdiskomconfig storage, 208omreport storage, 184versionomreport system, 76viewing alert actions for specific components and events, 63viewing

Index 272

28 omreport: Viewing System Status Using the Instrumentation ServiceConventions for Parameter TablesWhen listing the parameters that a command can tak

omreport: Viewing System Status Using the Instrumentation Service 29Table 3-2. Command Level 1, Level 2, and Level 3 for omreportCommand Level 1Comma

Contents 3Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 15What's New in Version 6.3 . . . . . . . . . . . . . . . 16Us

30 omreport: Viewing System Status Using the Instrumentation Servicefans U, P, A Shows the status and thresholds for system fans.firmware U, P, A Show

omreport: Viewing System Status Using the Instrumentation Service 31leds U, P, A Shows the properties you have set for light-emitting diodes to flash

32 omreport: Viewing System Status Using the Instrumentation Serviceremoteaccess U, P, A Shows general information on remote access.slots U, P, A Show

omreport: Viewing System Status Using the Instrumentation Service 33alertlog U, P, A Allows the administrator to display the alert log.assetinfo U, P,

34 omreport: Viewing System Status Using the Instrumentation Servicerecovery P, A Shows how your system is configured to respond to a hung operating s

omreport: Viewing System Status Using the Instrumentation Service 35Help With the omreport CommandUse the omreport -? command to get a list of the ava

36 omreport: Viewing System Status Using the Instrumentation Serviceomreport aboutUse the omreport about command to learn the product name and version

omreport: Viewing System Status Using the Instrumentation Service 37Server Administrator includes a number of services, each of which has a version nu

38 omreport: Viewing System Status Using the Instrumentation ServiceServer Administrator displays a general status for your main system chassis/main s

omreport: Viewing System Status Using the Instrumentation Service 39Server Administrator reports values for the Redundancy Status and Redundancy Mode

4 Contentsomreport about . . . . . . . . . . . . . . . . . . . . . 36omreport chassis/omreport mainsystem Commands. . 37omreport chassis/ omrepor

40 omreport: Viewing System Status Using the Instrumentation Service NOTE: All the BIOS Setup parameters are not displayed. Only those BIOS setup pro

omreport: Viewing System Status Using the Instrumentation Service 41NIC 1 Displays whether the first NIC is enabled (with or without PXE/iSCSI) or di

42 omreport: Viewing System Status Using the Instrumentation ServiceIDE Primary Drive 0 Displays whether the device is automatically detected and enab

omreport: Viewing System Status Using the Instrumentation Service 43To view all available boot devices, alias names, and boot order sequences, type:om

44 omreport: Viewing System Status Using the Instrumentation ServiceInternal Dual SD Module Redundancy : CriticalInternal SD Modules Statusomreport ch

omreport: Viewing System Status Using the Instrumentation Service 45The index parameter is optional. If you do not specify the index, Server Administr

46 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis fru oromreport mainsystem fruServer Administrator displays a summ

omreport: Viewing System Status Using the Instrumentation Service 47omreport chassis info index=noromreport mainsystem info index=nThe index parameter

48 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis intrusionA message that resembles the following displays:omreport

omreport: Viewing System Status Using the Instrumentation Service 49The index parameter is optional. If you do not specify the index, Server Administr

Contents 5omreport chassis processors/omreport mainsystem processors . . . . . . . . . . . . . . 51omreport chassis pwrmanagement/omreport mainsyst

50 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis nics/omreport mainsystem nicsUse the omreport chassis nics or omr

omreport: Viewing System Status Using the Instrumentation Service 51omreport chassis ports/omreport mainsystem portsUse the omreport chassis ports or

52 omreport: Viewing System Status Using the Instrumentation ServiceConnector Name is the name or number of the device that occupies the processor slo

omreport: Viewing System Status Using the Instrumentation Service 53The following fields are defined for a cache present on a particular microprocesso

54 omreport: Viewing System Status Using the Instrumentation ServiceA Write Policy describes how the cache deals with a write cycle. In a write-back p

omreport: Viewing System Status Using the Instrumentation Service 55omreport chassis pwrmanagement/omreport mainsystem pwrmanagement Use the omreport

56 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis pwrmonitoring/omreport mainsystem pwrmonitoringUse the omreport c

omreport: Viewing System Status Using the Instrumentation Service 57Power Consumption InformationPower ConsumptionIndexStatusProbe NameReadingWarning

58 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis pwrsupplies/omreport mainsystem pwrsuppliesUse the omreport chass

omreport: Viewing System Status Using the Instrumentation Service 59• Maximum Output Wattage•Online Status• Power Monitoring Capableomreport chassis r

6 Contentsomreport system summary/omreport servermodule summary . . . . . . . . . . . . . . 70omreport system thrmshutdown/omreport servermodule th

60 omreport: Viewing System Status Using the Instrumentation Serviceomreport chassis slots/omreport mainsystem slotsUse the omreport chassis slots or

omreport: Viewing System Status Using the Instrumentation Service 61omreport chassis volts/omreport mainsystem voltsUse the omreport chassis volts or

62 omreport: Viewing System Status Using the Instrumentation ServiceCommands for Viewing LogsYou can use the omreport system or omreport servermodule

omreport: Viewing System Status Using the Instrumentation Service 63Overall Health Status of the ESM LogWhen you type omreport system esmlog or omrepo

64 omreport: Viewing System Status Using the Instrumentation Service•Fan Warning •Fan Failure• Memory Pre-failure•Memory Failure• System Power Probe W

omreport: Viewing System Status Using the Instrumentation Service 65• Storage Controller Battery Warning• Storage Controller Battery Failure• Removabl

66 omreport: Viewing System Status Using the Instrumentation Service---------------Power Supplies----------------SettingsEnable: Informational, Warnin

omreport: Viewing System Status Using the Instrumentation Service 67Example Command for an Event TypeTy p e :omreport system events type=fansoromrepor

68 omreport: Viewing System Status Using the Instrumentation Serviceomreport system pedestinations/omreport servermodule pedestinationsUse the omrepor

omreport: Viewing System Status Using the Instrumentation Service 69omreport system platformevents/omreport servermodule platformeventsUse the omrepor

Contents 7omconfig chassis pwrmonitoring/omconfig mainsystem pwrmonitoring . . . . . . . . . . . . 112omconfig chassis remoteaccess/omconfig mainsys

70 omreport: Viewing System Status Using the Instrumentation Serviceomreport system shutdown/omreport servermodule shutdownUse the omreport system shu

omreport: Viewing System Status Using the Instrumentation Service 71Version : 6.x.xDescription : Systems Management SoftwareContains : Instrumentation

72 omreport: Viewing System Status Using the Instrumentation ServiceSlot Number : Slot 01-02Form Factor : Half Height Dual WidthRemote Access Informat

omreport: Viewing System Status Using the Instrumentation Service 73The system summary hardware information includes data values for installed compone

74 omreport: Viewing System Status Using the Instrumentation ServiceMain System Chassis/Main SystemChassis• Chassis Model• Chassis Service Tag• Chassi

omreport: Viewing System Status Using the Instrumentation Service 75Memory ArrayThe following details are listed for each memory board or module in th

76 omreport: Viewing System Status Using the Instrumentation ServiceStorage EnclosuresThe following details are listed for each storage enclosure atta

omreport: Viewing System Status Using the Instrumentation Service 77---------------------Main System Chassis---------------------Name : BIOSVers

78 omreport: Viewing System Status Using the Instrumentation Service

omconfig: Managing Components Using the Instrumentation Service 794omconfig: Managing Components Using the Instrumentation ServiceThe omconfig command

8 Contents5 omconfig system or servermodule assetinfo: Editing Cost of Ownership Values . . . . . . . . . . . . . . . . . . . . . . . . . . 151Overv

80 omconfig: Managing Components Using the Instrumentation ServiceConventions for Parameter TablesWhen listing the parameters that a command can take,

omconfig: Managing Components Using the Instrumentation Service 81Table 4-2. omconfig Command Level 1, Level 2, and Level 3Command Level 1Command Leve

82 omconfig: Managing Components Using the Instrumentation Servicewebserver A Allows the administrator to set the encryption levels of the Web server

omconfig: Managing Components Using the Instrumentation Service 83esmlog P, A Allows the administrator to clear the ESM log.events P, A Enables and di

84 omconfig: Managing Components Using the Instrumentation Servicechassis/ mainsystembiossetup A Configures the behavior of specific system components

omconfig: Managing Components Using the Instrumentation Service 85memorymode A Enables or disables the spare bank and mirroring memory modes, and also

86 omconfig: Managing Components Using the Instrumentation ServiceHelp With the omconfig CommandUse the omconfig -? command to get a list of the avail

omconfig: Managing Components Using the Instrumentation Service 87where | more allows you to press the spacebar to see the next screen of the CLI help

88 omconfig: Managing Components Using the Instrumentation ServiceHardware Application Programming Interface 5.x.xInstrumentation Service 6.x.xInstrum

omconfig: Managing Components Using the Instrumentation Service 89omconfig chassis/omconfig mainsystemUse the omconfig chassis or omconfig mainsystem

Contents 9Example Command for Adding Service Information . . . . . . . . . . . . . . . . . . . . . 163Adding Support Information. . . . . . . . . . .

90 omconfig: Managing Components Using the Instrumentation Serviceattribute=bezel setting=enabled | disabledenabled: Enables the bezel removal intrusi

omconfig: Managing Components Using the Instrumentation Service 91attribute=hddordersequence=aliasname1, aliasname2,... aliasnameNConfigures the BIO

92 omconfig: Managing Components Using the Instrumentation Serviceattribute=cstates setting=enabled | disabledenabled: Enables the processor to go int

omconfig: Managing Components Using the Instrumentation Service 93attribute=cpuxdsupportsetting=enabled | disabledenabled: Enables Execute Disable (XD

94 omconfig: Managing Components Using the Instrumentation Serviceattribute=dualnic setting=off | on | pxeboth | nic1pxe |nic2pxe | isciboth | nic1isc

omconfig: Managing Components Using the Instrumentation Service 95attribute=embvideoctrlsetting=enabled | disabledenabled: Enables the embedded video

96 omconfig: Managing Components Using the Instrumentation Serviceattribute=ide setting=on | offforce=trueon: Enables this device.off: Disables this d

omconfig: Managing Components Using the Instrumentation Service 97attribute=nic1 setting=enabled | enabledwithpxe | disabled | enabledonly | enabledno

98 omconfig: Managing Components Using the Instrumentation Serviceattribute=nic3 setting=enabled | enabledwithpxe | disabled | enabledonly | enabledno

omconfig: Managing Components Using the Instrumentation Service 99attribute=numlocksetting=on | off on: Uses the keypad as number keys.off: Uses the k