Dell PowerConnect 6024F Guía de usuario

www.dell.com | support.dell.comDell™ PowerConnect™ 6024/6024F SystemsUser’s Guide

10 ContentsViewing Interface Statistics . . . . . . . . . . . . . . . . . . . . . 391Viewing Etherlike Statistics . . . . . . . . . . . . . . . . .

110 Configuring System Informationwww.dell.com | support.dell.comResetting the Device Using the CLI1If you are not already in the Privileged User EXEC

Configuring System Information 111Polling for Anycast information is used when the server IP address is unknown. If this method is selected, all SNTP

112 Configuring System Informationwww.dell.com | support.dell.comFigure 6-7. SNTP Global SettingsThe SNTP Global Settings page contains the following

Configuring System Information 113Defining SNTP Global Parameters Using CLI CommandsThe following table summarizes the equivalent CLI commands for set

114 Configuring System Informationwww.dell.com | support.dell.comDefining SNTP Authentication MethodsThe SNTP Authentication page enables SNTP authent

Configuring System Information 115Figure 6-9. Add Authentication Key3Define the fields.4Click Apply Changes. The SNTP Authentication Key is added, and

116 Configuring System Informationwww.dell.com | support.dell.comDefining SNTP Authentication Settings Using CLI CommandsThe following table summarize

Configuring System Information 117Figure 6-11. SNTP ServersThe SNTP Servers page contains the following fields:SNTP Server — Contains a list of user-d

118 Configuring System Informationwww.dell.com | support.dell.comLast Response — The last time a response was received from the SNTP server.Offset — T

Configuring System Information 119Modifying an SNTP Server1Open the SNTP Servers page.2Click Show All.The SNTP Servers Table opens.3Select an SNTP Ser

Contents 1111 Getting HelpTechnical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 465Online Services. . . . . . . . . . . . . . .

120 Configuring System Informationwww.dell.com | support.dell.comDefining SNTP Interfaces The SNTP Broadcast Interface Table contains fields for setti

Configuring System Information 121Defining SNTP Interface Settings Using CLI CommandsThe following table summarizes the equivalent CLI commands for se

122 Configuring System Informationwww.dell.com | support.dell.comConfiguring Out-of-Band (OOB) Management PortsThis section describes managing the fol

Configuring System Information 123Facility—A user-defined application from which system logs are sent to the remote server. Only one facility can be a

124 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console(config)#logging oob/10.2.2.2

Configuring System Information 1252Define an IP address in the Default Gateway field. 3Click Apply Changes. The Out-of-Band Gateway device is defined,

126 Configuring System Informationwww.dell.com | support.dell.comFigure 6-17. OOB IP Interface ParametersThe OOB IP Interface Parameters page contains

Configuring System Information 127Deleting IP Addresses1Open the OOB IP Interface Parameters page.2Click Show All. 3The Interface Parameters Table pag

128 Configuring System Informationwww.dell.com | support.dell.comTACACS+ servers can be defined on in-band ports using TACACS+ Settings page or on the

Configuring System Information 129Status — The connection status between the device and the TACACS+ server. The possible field values are: Connected —

12 Contents

130 Configuring System Informationwww.dell.com | support.dell.comThe TACACS+ Table page opens.3Select a TACACS+ Table entry. 4Select the Remove check

Configuring System Information 131The following is an example of the CLI commands: Console(config)# tacacs-server host oob/172.16.8.1 key abcConsole (

132 Configuring System Informationwww.dell.com | support.dell.comConfiguring Out-of-Band RADIUS ServersThe OOB RADIUS Settings page contains both user

Configuring System Information 133Key String (0-128 Characters)—Key string used for authenticating and encrypting all RADIUS communications between th

134 Configuring System Informationwww.dell.com | support.dell.com3Select a RADIUS server and check the Remove checkbox. 4Click Apply Changes. The RADI

Configuring System Information 135Managing LogsThe Logs page contains links to various log pages. To display the Logs page, click System→ Logs in the

136 Configuring System Informationwww.dell.com | support.dell.comCritical — The third highest warning level. A critical log is saved if a critical dev

Configuring System Information 137Enabling Global Logs Using the CLI The following table summarizes the equivalent CLI commands for working with field

138 Configuring System Informationwww.dell.com | support.dell.comRAM Log TableThe RAM Log Table contains information about specific RAM (cache) log en

Configuring System Information 139Viewing the RAM Log Table Using the CLIThe following table summarizes the equivalent CLI commands for viewing fields

Introduction 23Introduction NOTICE: Before proceeding, read the release notes for this product. You can download the release notes from support.dell.

140 Configuring System Informationwww.dell.com | support.dell.comFigure 6-22. Log File TableThe Log File Table page contains the following fields:•Log

Configuring System Information 141The following is an example of the CLI commands: Console # show logging fileConsole Logging: Level info. Console Mes

142 Configuring System Informationwww.dell.com | support.dell.comFigure 6-23. Remote Log Server SettingsThe Remote Log Server Settings page contains t

Configuring System Information 1434Click Apply Changes. The log settings are saved, and the device is updated.Defining a New Server1Open the Remote Lo

144 Configuring System Informationwww.dell.com | support.dell.comDefining IP InterfacesThe IP Interface Parameters page contains parameters for assign

Configuring System Information 145Remove — When checked, removes the interface from the IP Address drop-down menu.Adding an IP Interface1Open the IP I

146 Configuring System Informationwww.dell.com | support.dell.comDefining IP Interface Parameters Using CLI CommandsThe following table summarizes the

Configuring System Information 147Defining DHCP IP Interface ParametersThe DHCP IP Interface page specifies the DHCP clients connected to the device.

148 Configuring System Informationwww.dell.com | support.dell.comModifying a DHCP IP Interface1Open the DHCP IP Interface page.2Modify the fields.3Cli

Configuring System Information 149Figure 6-27. Domain Naming System (DNS)The Domain Naming System (DNS) page contains the following fields:DNS Status

24 Introductionwww.dell.com | support.dell.comPowerConnect 6024FPowerConnect 6024F provides 24 SFP ports with 8 10/100/1000 Base-T RJ-45 combo ports t

150 Configuring System Informationwww.dell.com | support.dell.comThe Add DNS Server page contains the following fields:DNS Server — Specifies the DNS

Configuring System Information 151Configuring DNS Servers Using the CLI CommandsThe following table summarizes the CLI commands for configuring DNS se

152 Configuring System Informationwww.dell.com | support.dell.comFigure 6-30. Default Domain NameThe Default Domain Name page contains the following f

Configuring System Information 153Mapping the Domain HostThe Host Name Mapping page provides parameters for assigning an IP address to a static host n

154 Configuring System Informationwww.dell.com | support.dell.comFigure 6-32. Add Host Name Mapping3Define the relevant fields. 4Click Apply Changes.

Configuring System Information 155The following is an example of the CLI commands: Console(config)# ip host accounting.abc.com 176.10.23.1Table 6-22.

156 Configuring System Informationwww.dell.com | support.dell.comEnabling ARP ProxyAddress Resolution Protocol (ARP) is a TCP/IP protocol that convert

Configuring System Information 157Enabling ARP Proxy Using CLI CommandsThe following table contains the CLI commands for enabling the ARP Proxy. The f

158 Configuring System Informationwww.dell.com | support.dell.comThe ARP Settings page contains the following fields:Global Settings — Select this opt

Configuring System Information 159Figure 6-36. Add ARP Entry Page3Select an interface and complete the fields in the page. 4Click Apply Changes. The A

Introduction 25Standard wiring for end stations is Media-Dependent Interface (MDI) and the standard wiring for hubs and switches is known as Media-Dep

160 Configuring System Informationwww.dell.com | support.dell.comConfiguring ARP Using the CLI CommandsThe following table contains the CLI commands f

Configuring System Information 161Figure 6-37. DHCP RelayEnabling DHCP Relay1Open the DHCP Relay page.2Select Enable from the DHCP Relay drop-down men

162 Configuring System Informationwww.dell.com | support.dell.comDeleting a DHCP Relay Table Entry1Open the DHCP Relay page.2Click Show All to open th

Configuring System Information 163Configuring UDP RelayUDP Relay allows UDP packets to reach other networks. This feature enables browsing from workst

164 Configuring System Informationwww.dell.com | support.dell.comDestination Address — The IP interface that receives UDP packet relays. If this field

Configuring System Information 1654Click Apply Changes. The DHCP Server is added to the DHCP Relay Table.Modifying a UDP Relay Table Entry NOTE: If U

166 Configuring System Informationwww.dell.com | support.dell.comRunning Cable DiagnosticsUse the Diagnostics page to perform virtual cable tests for

Configuring System Information 167Open Cable — The cable is open.Short Cable — A short has occurred in the cable.OK — The cable passed the test.Fiber

168 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console# show copper-ports cable-len

Configuring System Information 169Figure 6-40. Optical Transceiver DiagnosticsThe Optical Transceiver Diagnostics page contains the following fields:P

26 Introductionwww.dell.com | support.dell.comMAC Address Supported FeaturesMAC Address SupportThe switch supports up to 16K MAC addresses and reserve

170 Configuring System Informationwww.dell.com | support.dell.comPerforming Fiber Optic Cable Tests Using CLI CommandsThe following table contains the

Configuring System Information 171Management access can be separately defined for each type of management access method, including, Web (HTTP), Secure

172 Configuring System Informationwww.dell.com | support.dell.comAdding an Access Profile1Open the Access Profiles page.2Click Add Profile to open the

Configuring System Information 1733Enter the profile name in the Access Profile Name text box.4Complete the fields and click Apply Changes. The new ac

174 Configuring System Informationwww.dell.com | support.dell.com3Select a rule.4Check the Remove check box and click Apply Changes. The rule is delet

Configuring System Information 175The following is an example of the CLI commands:Console (config)# management access-list mlistConsole (config-macl)#

176 Configuring System Informationwww.dell.com | support.dell.comOptional Methods — User authentication methods. Possible options are:None — No user a

Configuring System Information 1774Click Apply Changes. The entry is removed.Configuring an Authentication Profile Using CLI CommandsThe following tab

178 Configuring System Informationwww.dell.com | support.dell.comFigure 6-45. Select AuthenticationThe Select Authentication page contains the followi

Configuring System Information 179Local, RADIUS — Authentication first occurs locally. If authentication cannot be verified locally, the RADIUS server

Introduction 27For information about configuring port mirroring, see "Defining Port Mirroring Sessions."Broadcast Storm ControlWhen Layer 2

180 Configuring System Informationwww.dell.com | support.dell.comApplying an Authentication Profile to Secure Telnet (SSH) Sessions1Open the Select Au

Configuring System Information 181The following is an example of the CLI commands: Console# show authentication methodsLogin Authentication Method Lis

182 Configuring System Informationwww.dell.com | support.dell.comManaging PasswordsPassword management provides increased network security and improve

Configuring System Information 183 NOTE: The user is notified to change the password prior to expiry. The Web users do not see this notification.Enab

184 Configuring System Informationwww.dell.com | support.dell.comConsole# show passwords configurationMinimal length: 8Aging: 120 daysHistory: 2Lock-

Configuring System Information 185Confirm Password — Confirms the user-defined password.Remove — When selected, removes users from the User Name list.

186 Configuring System Informationwww.dell.com | support.dell.comAssigning Users Using CLI CommandsThe following table summarizes the equivalent CLI c

Configuring System Information 187Figure 6-48. Line PasswordThe Line Password page contains the following fields:Line Password for Console/Telnet/Secu

188 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config-line)# password ****

Configuring System Information 1893Click Apply Changes. The new password is defined, and the device is updated.Assigning Enable Passwords Using CLI Co

28 Introductionwww.dell.com | support.dell.comPrivate VLAN EdgePrivate VLAN Edge (PVE) ports are a Layer 2 security feature that provides port-based s

190 Configuring System Informationwww.dell.com | support.dell.comThe TACACS+ Settings page contains both user-defined and the default TACACS+ settings

Configuring System Information 191Status — The connection status between the device and the TACACS+ server. The possible field values are: Connected —

192 Configuring System Informationwww.dell.com | support.dell.comDeleting a TACACS+ Server from the TACACS+ Servers List1Open the TACACS+ Settings pag

Configuring System Information 193The following is an example of the CLI commands: show tacacs+ [ip-address] Displays configuration and statistics for

194 Configuring System Informationwww.dell.com | support.dell.comConfiguring RADIUS SettingsRemote Authorization Dial-In User Service (RADIUS) servers

Configuring System Information 195Timeout for Reply (1-30) — Amount of the time in seconds the device waits for an answer from the RADIUS server befor

196 Configuring System Informationwww.dell.com | support.dell.comModifying the RADIUS Server settings1Open the RADIUS Settings page.2Click Show All to

Configuring System Information 197The following is an example of CLI commands: Console (config)# radius-server timeout 5Console (config)# radius-serve

198 Configuring System Informationwww.dell.com | support.dell.com•Timeliness — Protects against message delay or message redundancy. The SNMP agent co

Configuring System Information 199Authentication Notifications — Enables or disables the device sending SNMP traps when authentication fails. Enabling

Introduction 29Link AggregationLink Aggregation Up to seven ports can combine to form a single Link Aggregated Group (LAG). This enables fault toleran

200 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of CLI commands:Console (config)# snmp-server enable trap

Configuring System Information 201Defining SNMP ViewsSNMP views provide or block access to device features or feature aspects. For example, a view can

202 Configuring System Informationwww.dell.com | support.dell.comFigure 6-54. Add A View 3Define the relevant fields.4Click Apply Changes. The SNMP vi

Configuring System Information 2035Click Apply Changes. The SNMP view is deleted, and the device is updated. Defining SNMP Views Using CLI CommandsThe

204 Configuring System Informationwww.dell.com | support.dell.comDefining SNMP Access ControlThe Access Control Group page provides information for cr

Configuring System Information 205Authentication — Authenticates SNMP messages without encrypting them.Privacy — Authenticates SNMP messages and encry

206 Configuring System Informationwww.dell.com | support.dell.comDisplaying the Access Table1Open the Access Control Group page.2Click Show All.The Ac

Configuring System Information 207The following is an example of the CLI commands:Console (config)# snmp-server group user-group v3 priv read user-vie

208 Configuring System Informationwww.dell.com | support.dell.comFigure 6-59. SNMPv3 User Security Model (USM)The SNMPv3 User Security Model (USM) pag

Configuring System Information 209SHA Key — Users are authenticated using the HMAC-SHA-96 authentication level. The user should enter authentication a

Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates

30 Introductionwww.dell.com | support.dell.comAddress Resolution Protocol (ARP)In IP routing, routers and Layer 3 switches use various routing protoco

210 Configuring System Informationwww.dell.com | support.dell.comFigure 6-61. SNMPv3 User Security Model TableDeleting a User Security Model Table Ent

Configuring System Information 211Defining CommunitiesAccess rights are managed by defining communities on the SNMPv1, 2 Community page. When the comm

212 Configuring System Informationwww.dell.com | support.dell.comFigure 6-62. SNMPv1, 2 CommunityThe SNMPv1, 2 Community page contains the following f

Configuring System Information 213View Name — Contains a list of user-defined SNMP viewsAdvanced — Contains a list of user-defined groups. When SNMP A

214 Configuring System Informationwww.dell.com | support.dell.comDeleting Communities1Open the SNMPv1, 2 Community page.2Click Show All.The SNMPv1,2 C

Configuring System Information 215Figure 6-64. Notification FilterThe Notification Filter page contains the following fields:Notification Filter Name

216 Configuring System Informationwww.dell.com | support.dell.comFigure 6-65. Add Filter3Define the relevant fields. 4Click Apply Changes. The new fil

Configuring System Information 217Configuring Notification Filters Using CLI CommandsThe following table summarizes equivalent CLI commands for defini

218 Configuring System Informationwww.dell.com | support.dell.comFigure 6-67. Notification RecipientsThe Notification Recipients page contains the fol

Configuring System Information 219SNMPv3 — SNMP version 3 is enabled for the selected recipient. The possible field values are: User Name — Contains a

Introduction 31Layer 3 FeaturesTCPTransport Control Protocol (TCP) connections are defined between 2 ports by an initial synchronization exchange. TCP

220 Configuring System Informationwww.dell.com | support.dell.comFigure 6-68.Add Notification Recipient 3Define the relevant fields.4Click Apply Chang

Configuring System Information 221Deleting Notification Recipients1Open the Notification Recipients page.2Click Show All. The Notification Recipients

222 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of CLI commands: Console (config)# snmp-server host 12.1.

Configuring System Information 223Managing FilesUse the File Management page to manage device software, the image file, and the configuration files. F

224 Configuring System Informationwww.dell.com | support.dell.comTo open the File Management page, click System→ File Management in the tree view. Dow

Configuring System Information 225Active Image — Image file that is currently active.Active Image After Reset — The image file that is active after th

226 Configuring System Informationwww.dell.com | support.dell.comDownloading Files Using CLI CommandsThe following table summarizes the equivalent CLI

Configuring System Information 227Figure 6-71. File Upload to ServerThe File Upload to Server page contains the following fields:Firmware Upload — Ind

228 Configuring System Informationwww.dell.com | support.dell.comConfiguration Upload via OOB—Indicates that the Configuration file is uploaded via th

Configuring System Information 229Figure 6-72. Copy FilesThe Copy Files page contains the following fields:Copy Configuration — Specifies that a confi

32 Introductionwww.dell.com | support.dell.comClass Of Service 802.1p SupportThe IEEE 802.1p signaling technique is an OSI Layer 2 standard for taggin

230 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console# delete startup-configDefini

Configuring System Information 231The General Settings page contains the following fields:Current — Maximum number of entries.After Reset— Maximum num

232 Configuring System Informationwww.dell.com | support.dell.com

Configuring Switch Information 233Configuring Switch InformationThis section provides all system operations and general information for configuring ne

234 Configuring Switch Informationwww.dell.com | support.dell.comAdvanced Port Based Authentication also enables VLAN based authentication. Specific V

Configuring Switch Information 235The Port Based Authentication page contains the following fields:Port Based Authentication State — Permits port base

236 Configuring Switch Informationwww.dell.com | support.dell.comQuiet Period (1-65535) — Defines the amount of time that the device remains in the qu

Configuring Switch Information 2375Click Apply Changes. The parameters are copied to the selected port in the Port Based Authentication Table, and the

238 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: dot1x timeout tx-period seconds Sets

Configuring Switch Information 239Configuring Advanced Port Based AuthenticationThe Multiple Hosts page provides information for defining advanced por

Introduction 33Trivial File Transfer Protocol (TFTP)PowerConnect 6024/6024F supports boot image, firmware and configuration upload/download via TFTP.R

240 Configuring Switch Informationwww.dell.com | support.dell.comStatus — The host status. The possible field values are: Unauthorized — Indicates tha

Configuring Switch Information 241The following is an example of the CLI Command.Authenticating UsersThe Authenticated Users page displays user port a

242 Configuring Switch Informationwww.dell.com | support.dell.comMAC Address — The supplicant MAC address.Displaying the Authenticated Users Table1Ope

Configuring Switch Information 243protection mechanism is invoked, and can provide various options. Unauthorized packets arriving to a locked port are

244 Configuring Switch Informationwww.dell.com | support.dell.comDefining a Locked Port1Open the Port Security page.2Select an interface type and numb

Configuring Switch Information 245The following is an example of the CLI commands: Defining IP based ACLsAccess control lists (ACL) allow network mana

246 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-8. Add ACE to IP Based ACLThe Add ACE to IP Based ACL page contains the foll

Configuring Switch Information 247Wild Card Mask — The Destination IP address wildcard mask. Select either Match DSCP or Match IP Precedence:Match DSC

248 Configuring Switch Informationwww.dell.com | support.dell.comModifying an IP based ACE NOTE: ACEs can be modified only when the ACL to which they

Configuring Switch Information 249The IP based ACL is removed, and the device is updated.Assigning IP based ACEs to ACLs Using the CLI CommandsThe fol

34 Introductionwww.dell.com | support.dell.comOut-of-Band Management Port SupportAn out-of-band management port is an external Ethernet port that carr

250 Configuring Switch Informationwww.dell.com | support.dell.comDefining MAC based ACLsThe Add ACE to MAC Based ACL page allows network administrator

Configuring Switch Information 251VLAN ID — Matches the packet’s VLAN ID to the ACE. The possible field values are 1-4094.Action — Indicates the ACL f

252 Configuring Switch Informationwww.dell.com | support.dell.comAdding ACEs to a MAC based ACL NOTE: ACEs can be added only if the ACL is not bound

Configuring Switch Information 253The following is an example of the CLI commands: Console(config)# mac access-list dellConsole(config-mac-al)# permit

254 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-12. ACL BindingsThe ACL Bindings page contains the following fields:Select a

Configuring Switch Information 2554Click Apply Changes. The selected entry is removed from the table, and the device is updated.Displaying the ACL Bin

256 Configuring Switch Informationwww.dell.com | support.dell.comConsole (config-cmap)# exitConsole (config)# exitConsole> exitConsole> show cla

Configuring Switch Information 257Admin Status — Enables or disables traffic forwarding through the port.Current Port Status — Specifies whether the p

258 Configuring Switch Informationwww.dell.com | support.dell.comNeighbor Advertisement — The neighbor port (the port to which the selected interface

Configuring Switch Information 259Displaying the Port Table1Open the Port Configuration page.2Click Show All to display the Port Configuration Table.

Introduction 35RADIUS ClientRADIUS is a client/server-based protocol in which the server maintains a user database, that contains per-user authenticat

260 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# interface ethernet

Configuring Switch Information 261Console> show interfaces statusConsole# show interfaces configurationFlow Link Back MdixPort Type Duplex Speed Ne

262 Configuring Switch Informationwww.dell.com | support.dell.comConsole# show interfaces description ethernet 1Defining LAG ConfigurationMultilayer s

Configuring Switch Information 263The LAG Configuration page contains the following fields:LAG — Contains a list of LAG numbers.Description (0-64 Char

264 Configuring Switch Informationwww.dell.com | support.dell.com4Click Apply Changes. The LAG parameters are saved to the device.Displaying the LAG C

Configuring Switch Information 265Enabling Storm ControlA broadcast storm is the result of an excessive amount of broadcast messages simultaneously tr

266 Configuring Switch Informationwww.dell.com | support.dell.comModifying Storm Control Port Parameters1Open the Storm Control page.2Complete the fie

Configuring Switch Information 267Console(config-if)# port storm-control broadcast rate 100000Console(config-if)# exitDefining Port Mirroring Sessions

268 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-16. Port MirroringThe Port Mirroring page contains the following fields:Dest

Configuring Switch Information 2694Click Apply Changes. The new port mirroring session is enabled for the port, and the device is updated.Modifying a

36 Introductionwww.dell.com | support.dell.com

270 Configuring Switch Informationwww.dell.com | support.dell.comDefining Static AddressesThe Static Address page contains a list of static MAC addres

Configuring Switch Information 271Adding a Static MAC Address1Open the Static MAC Address page.2Click Add to display the Add Static MAC Address page.3

272 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: console (config)# interface vlan 1 c

Configuring Switch Information 273Figure 7-18. Dynamic Address TableThe Dynamic Address Table contains the following fields:Address Aging (10-630) — S

274 Configuring Switch Informationwww.dell.com | support.dell.comEntries can be queried by Port, MAC Address, or VLAN ID. 3Click Query. The Dynamic Ad

Configuring Switch Information 275vlan mac address port type---- -------------- ----- -----1 0060.704C.73FF g8 dynamic 1 0060.708C.73FF g8 dynamic 200

276 Configuring Switch Informationwww.dell.com | support.dell.comGARP Leave Timer (10 - 2147483640) — Time lapse, in milliseconds, that the device wai

Configuring Switch Information 277The following is an example of the CLI commands: Console (config)# interface ethernet g8Console (config-if)# garp ti

278 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-20. Spanning Tree Global SettingsThe Spanning Tree Global Settings page cont

Configuring Switch Information 279Hello Time (1-10) — The switch Hello time, which indicates the amount of time in seconds a root bridge waits between

Hardware Description 37Hardware DescriptionThis section contains information about device characteristics and module hardware configurations.Ports Des

280 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console(config)# spanning-treeConsol

Configuring Switch Information 281Spanning tree enabled mode RSTPRoot ID Priority 32768Address 0001.4297.e000Cost 57Port g1Hello Time 2 sec Max Age 20

282 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-21. STP Port SettingsThe STP Port Settings page contains the following field

Configuring Switch Information 283Forwarding — The port is currently in the forwarding mode. The port can forward traffic and learn new MAC addresses.

284 Configuring Switch Informationwww.dell.com | support.dell.comDefining STP Port Settings Using CLI CommandsThe following table summarizes the equiv

Configuring Switch Information 285Port Fast: no (configured: no)Defining STP LAG SettingsUse the STP LAG Settings page to assign STP aggregating ports

286 Configuring Switch Informationwww.dell.com | support.dell.comBlocking — The LAG is blocked and cannot be used to forward traffic or learn MAC addr

Configuring Switch Information 287The following is an example of the CLI commands: Console(config)# interface port-channel 1Console(config-if)# spanni

288 Configuring Switch Informationwww.dell.com | support.dell.comDefining the Rapid Spanning TreeWhile the classic spanning tree prevents Layer 2 forw

Configuring Switch Information 289Point-to-Point Operational Status — The Point-to-Point operating state. Activate Protocol Migration Test — When chec

38 Hardware Descriptionwww.dell.com | support.dell.comPowerConnect 6024FThe PowerConnect 6024F ports differ from the PowerConnect 6024 only in port de

290 Configuring Switch Informationwww.dell.com | support.dell.comIn addition, packets assigned to various VLANs are transmitted along different paths

Configuring Switch Information 291Designated Root Bridge ID — Indicates the ID of the bridge with the lowest path cost to the instance root.Root Port

292 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console(config)# spanning-tree mst c

Configuring Switch Information 293Defining MSTP Interface SettingsUse the MSTP Interface Setting page to assign MSTP settings to specific interfaces.

294 Configuring Switch Informationwww.dell.com | support.dell.comTy pe — Indicates whether MSTP treats the port as a point-to-point port or a port co

Configuring Switch Information 295Figure 7-27. MSTP Interface TableDefining MSTP Interfaces Using CLI CommandsThe following table summarizes the equiv

296 Configuring Switch Informationwww.dell.com | support.dell.comRoot Port 1 (ig)Hello Time 2 sec Max Age 20 sec Forward Delay 15 secIST Mas

Configuring Switch Information 297Figure 7-28. VLAN Membership PageThe VLAN Membership page is divided into the VLAN Membership Table and the VLAN Por

298 Configuring Switch Informationwww.dell.com | support.dell.comAdding New VLANs1Open the VLAN Membership page.2Click Add to display the Create New V

Configuring Switch Information 299VLAN Port Membership TableThe VLAN Port Membership Table contains a Port Table for assigning ports to VLANs. Ports a

Hardware Description 39Hardware ComponentsPhysical DimensionsThe switch has the following physical dimensions:• 440 x 460 x 44 mm (W x D x H).• 17.32

300 Configuring Switch Informationwww.dell.com | support.dell.comAssigning Ports to VLAN Groups Using CLI CommandsThe following table contains the CLI

Configuring Switch Information 301Port VLAN Mode — Indicates the port mode. Possible values are:General — The port belongs to VLANs, and each VLAN is

302 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# interface ethernet

Configuring Switch Information 303Defining VLAN LAG SettingsThe VLAN LAG Settings page provides parameters for managing LAGs that are part of a VLAN.

304 Configuring Switch Informationwww.dell.com | support.dell.comIngress Filtering — Enables or disables Ingress filtering by the LAG. Ingress filteri

Configuring Switch Information 305The following is an example of the CLI commands: Console (config-if)# switchport mode accessConsole (config-if)# swi

306 Configuring Switch Informationwww.dell.com | support.dell.comAdding a Protocol Group1Open the Protocol Group page.2Click Add to display the Assign

Configuring Switch Information 307Figure 7-32. Protocol Port PageInterface — Port or LAG number added to a protocol group.Protocol Group ID — Protocol

308 Configuring Switch Informationwww.dell.com | support.dell.comThe following example sets a protocol-based classification rule of protocol group 1 t

Configuring Switch Information 309Figure 7-33. GVRP Global Parameters PageGVRP Global Status — Enables or disables GVRP on the device. GVRP is disable

Contents 3Contents1 IntroductionPowerConnect 6024 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23PowerConnect 6024F. . . . . . . . . . . .

40 Hardware Descriptionwww.dell.com | support.dell.comWhen you connect to a different power source, the probability of the switch failing in the event

310 Configuring Switch Informationwww.dell.com | support.dell.comConfiguring GVRP Using CLI CommandsThe following table summarizes the equivalent CLI

Configuring Switch Information 311Maximum VLANs: 4063, Maximum VLANs after reset: 4063.Port(s) GVRP-Status Registration Dynamic VLAN Timers(milliseco

312 Configuring Switch Informationwww.dell.com | support.dell.comConsole# clear gvrp statistics ethernet g8Aggregating Ports Link Aggregation optimize

Configuring Switch Information 313• PowerConnect 6024/6024F supports up to seven LAGs.• Ports can be configured as LACP ports only if the ports are no

314 Configuring Switch Informationwww.dell.com | support.dell.comThe LACP Parameters page contains sections for defining global parameters and port pa

Configuring Switch Information 315The following is an example of the CLI commands: Console (config)# lacp system-priority 120Console (config)# interfa

316 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-35. LAG Membership PageLACP — Aggregates the port to a LAG, using LACP.LAG —

Configuring Switch Information 317Console (config)# interface port-channel 1Console (config-if)# channel-group 1 mode onConsole# show interfaces port-

318 Configuring Switch Informationwww.dell.com | support.dell.comWhen IGMP Snooping is enabled globally, all IGMP packets are forwarded to the CPU. Th

Configuring Switch Information 3193Click Apply Changes.Bridge Multicast is enabled on the device.Enabling IGMP Snooping on the Device1Open the Multica

Hardware Description 41SFP Port LEDsFigure 2-5 illustrates the SFP port LEDs that are next to each SFP port.Figure 2-5. SFP Port LEDsTable 2-1 contain

320 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-37. Bridge Multicast Group PageVLAN ID — Identifies a VLAN and contains info

Configuring Switch Information 321Adding Bridge Multicast Addresses1Open the Bridge Multicast Group page.2Click Add to display the Add Bridge Multicas

322 Configuring Switch Informationwww.dell.com | support.dell.comAssigning LAGs to Receive Multicast Service1Open the Bridge Multicast Group page.2Def

Configuring Switch Information 323console(config)#interface range ethernet g1-9console(config-if)# switchport mode generalconsole(config-if)# switchpo

324 Configuring Switch Informationwww.dell.com | support.dell.comFigure 7-39. Bridge Multicast Forward All PageVLAN ID — Identifies a packet VLAN and

Configuring Switch Information 3254Click Apply Changes. The port is attached to the multicast router or switch.Attaching a LAG to a Multicast Router o

326 Configuring Switch Informationwww.dell.com | support.dell.comconsole#configconsole(config)#vlan databaseconsole(config-if)#vlan 8console(config-vl

Configuring Switch Information 327Figure 7-40. IGMP SnoopingVLAN ID — Specifies the VLAN ID.IGMP Snooping Status — Enables or disables IGMP snooping o

328 Configuring Switch Informationwww.dell.com | support.dell.com2Click Show All to display the IGMP Snooping Table.Configuring IGMP Snooping with CLI

Configuring Switch Information 329Console (config)# exitConsole # show ip igmp snooping interface 1000IGMP Snooping is globally enabledIGMP Snooping i

42 Hardware Descriptionwww.dell.com | support.dell.comTable 2-2 contains 10/100/1000 Base-T port LED definitions.System LEDsThe system LEDs, located o

330 Configuring Switch Informationwww.dell.com | support.dell.com

Configuring Routing 331Configuring RoutingRouting OverviewDevices in different subnetworks communicate with each other using a Layer 3 router between

332 Configuring Routingwww.dell.com | support.dell.comFigure 8-1. IP Forwarding PageMaximum Equal Cost Multipaths (ECMP) — The ECMP value, which must

Configuring Routing 333Viewing IP Forwarding Using the CLI CommandsThe following table contains the CLI commands for viewing IP Forwarding. The follow

334 Configuring Routingwww.dell.com | support.dell.comConfiguring IP Static RoutesUse the IP Static Route page to define static routes.To open the IP

Configuring Routing 3351Open the IP Static Route page.2Define the fields on the page. NOTE: Selecting a Route Type of Reject ensures routes to the d

336 Configuring Routingwww.dell.com | support.dell.comConfiguring VRRPVirtual Router Redundancy Protocol (VRRP) specifies an elector protocol that dyn

Configuring Routing 337MAC, and accepts packets associated with the virtual IP addresses (only if the router owns the associated IP address).Initializ

338 Configuring Routingwww.dell.com | support.dell.com3Define the fields.See "Configuring VRRP" for information about the fields. NOTE: VRR

Configuring Routing 339Configuring VRRP Using the CLI CommandsThe following is an example of the CLI commands: Console(config)# interface ethernet g8C

Hardware Description 43Figure 2-7. System LEDs Table 2-3 contains system LED definitions.Table 2-3. System LED DefinitionsLED Color DefinitionFan 1Gre

340 Configuring Routingwww.dell.com | support.dell.comConfiguring MD5 Routing AuthenticationMD5 keys are used by the Message Digest-5 Authentication A

Configuring Routing 341Stop Generating At — Date and time the protocol packets are no longer forwarded with MD5 keys. The Stop Generate field format i

342 Configuring Routingwww.dell.com | support.dell.com3Select an entry in the Key ID field.4Check the Remove check box.5Click Apply Changes. The MD5 K

Configuring Routing 343The following is an example of the CLI commands: Console (config)# key 3Console (config-key)# accept-lifetime duration 13:30:00

344 Configuring Routingwww.dell.com | support.dell.comMD5 Key — The key that is a key chain member.Accept From — Date and time the selected MD5 key be

Configuring Routing 345Configuring Key Chains Using CLI CommandsThe following table contains the CLI commands for configuring the key chains.The follo

346 Configuring Routingwww.dell.com | support.dell.comkey chain internalkey 1accept: 13:30:00 Jan 25 2002 duration 7200send: 14:00:00 Jan 25 200

Configuring Routing 347Click Router→ RIP→ Global Parameters in the tree view to display the RIP Global Parameters page.Figure 8-8. RIP Global Paramete

348 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# router rip enableConsole (con

Configuring Routing 349Figure 8-9. RIP Interface Parameters PageRIP Interface — The current interface IP address.RIP Version — The type of RIP being b

44 Hardware Descriptionwww.dell.com | support.dell.comPWR2Green Power Supply 2 is present and operating. Red Power Supply 2 is present, but not operat

350 Configuring Routingwww.dell.com | support.dell.comDefault Route Metric (1-16) — The default route entry metric in RIP updates originating on this

Configuring Routing 351Configuring RIP Interfaces Using CLI CommandsThe following table contains the CLI commands for configuring the RIP Global Param

352 Configuring Routingwww.dell.com | support.dell.comConsole# show ip ripRIP is enabled.OSPF leaking is enabled.Static leaking is enabled.Interface S

Configuring Routing 353Figure 8-10. OSPF Global Parameters PageOSPF Status — Enables OSPF on at least one interface, or disables OSPF for all interfac

354 Configuring Routingwww.dell.com | support.dell.comEnabling OSPF1Open the OSPF Parameters page. 2Define the OSPF Status, Router ID, Redistribute RI

Configuring Routing 355Figure 8-11. OSPF Areas Page Area ID — The area ID. The format is an IP address.Import Autonamous System External — Indicates w

356 Configuring Routingwww.dell.com | support.dell.comRemove — When checked, removes the IP address from the OSPF area table. Defining a New OSPF Area

Configuring Routing 357The following is an example of the CLI commands: Console (config)# router ospf enableConsole (config)# router ospf area 7.7.7.7

358 Configuring Routingwww.dell.com | support.dell.comHello Interval (1-65535) — Time (seconds) between Hello packets. All devices attached to a commo

Configuring Routing 3593Define the fields in the page.4Click Apply Changes. The new OSPF virtual link is added.Modifying Virtual Links1Open the Virtua

Cable, Port, and Pinout Information 45Cable, Port, and Pinout InformationThis section describes the switch’s physical interfaces and provides informat

360 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# show ip ospf virtual-linksVir

Configuring Routing 361Figure 8-14.Interface Parameters PageOSPF Interface — IP address of the OSPF interface.Priority — The interface priority. Value

362 Configuring Routingwww.dell.com | support.dell.comAuthentication Mode — The interface authentication type, Password or MD5, used to authenticate O

Configuring Routing 363Modifying OSPF Parameters1Open the Interface Parameters page. 2Select an OSPF interface to display the field parameters for the

364 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console(config)# interface ip 1.100.100.100Cons

Configuring Routing 365Transmit Delay is 1 sec, State OTHER, Priority 1Designated Router id 192.168.1.11, Interface address 192.168.1.11Backup Designa

366 Configuring Routingwww.dell.com | support.dell.comViewing the OSPF Link State Table Using CLI CommandsThe following table contains the CLI command

Configuring Routing 367Figure 8-17. External Link State TableLink Type — The external link type. Each link state advertisement has a specific format.

368 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console> show ip ospf databaseViewing the OS

Configuring Routing 369Displaying the All Neighbors Table1Open the Neighbors Table page.2Click Show All to display the All Neighbors Table.Viewing the

46 Cable, Port, and Pinout Informationwww.dell.com | support.dell.comPin Connections for SFP InterfacesFigure 3-2 illustrates an SFP connector, and Ta

370 Configuring Routingwww.dell.com | support.dell.comConfiguring IP Multicast RoutingMulticast routing maximizes network resources. One host sends da

Configuring Routing 371The following is an example of the CLI commands: Console (config)# ip multicast-routingDefining IGMP Interface ParametersIntern

372 Configuring Routingwww.dell.com | support.dell.comMax Query Response Time (0-25) — Maximum response time for advertising IGMP queries. Response ti

Configuring Routing 373The following is an example of the CLI commands: Console (config)# interface ethernet g1Console (config-if)# ip igmpConsole (co

374 Configuring Routingwww.dell.com | support.dell.comDefining IGMP Static Interface GroupsThe IGMP Static Group Table enables static definition of IG

Configuring Routing 375The page contains the following fields: •Interface — The IP Multicast Group address of which the port is a member.•IP Multicast

376 Configuring Routingwww.dell.com | support.dell.comFigure 8-22. IGMP Dynamic Group TableInterface — Specifies an interface belonging to the IP Mult

Configuring Routing 377The following is an example of CLI commands:Console> show ip igmp groupsGroup Address Interface Uptime Expires Last Repor

378 Configuring Routingwww.dell.com | support.dell.comFigure 8-23. DVMRP InterfaceThe DVMRP Interface page contains the following fields divided into

Configuring Routing 3792Click Add to display the Add a DVMRP Interface page. 3Define the interface number and DVMRP metric.4Click Apply Changes. The D

Cable, Port, and Pinout Information 47Serial Cable ConnectionYou can use serial cables (null-modem) to connect the switch to a terminal for initial se

380 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI command:Console (config-if)# interface ethernet g5Console

Configuring Routing 381Viewing the DVMRP Prune Table Using CLI Commands The following table contains the CLI command for viewing the Prune Table.The f

382 Configuring Routingwww.dell.com | support.dell.comUpstream Neighbor — IP address of the upstream RPF neighbor, from which source IP datagrams are

Configuring Routing 383Figure 8-26. DVMRP Next Hop TableSource IP Address — Source IP address for the next hop of an outgoing interface.Source Mask —

384 Configuring Routingwww.dell.com | support.dell.comDVMRP Neighbor TableThe DVMRP Neighbor Table page contains information about neighboring port in

Configuring Routing 385Console> show ip dvmrp neighbor ethernet g1Interface Neighbor Up Expiry Version Capabilities RCV BadState Time Time

386 Configuring Routingwww.dell.com | support.dell.comSource Mask — Masks all or parts of the source IP address.Upstream Neighbor — IP address of the

Configuring Routing 387Viewing the IP Multicast Next Hop TableThe IPM Next Hop Table page contains multicast next hop information. To open the page, c

388 Configuring Routingwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console> show ip mroute-next-hopGroup

Viewing Statistics 389Viewing StatisticsThis section contains statistics on interface, GVRP, etherlike, RMON, and device utilization. NOTE: CLI comma

48 Cable, Port, and Pinout Informationwww.dell.com | support.dell.comFigure 3-3. Serial ConnectorTable 3-3 contains serial cable pin assignments. Conn

390 Viewing Statisticswww.dell.com | support.dell.comThe Utilization Summary page contains the following fields:Refresh Rate — Amount of time that pas

Viewing Statistics 391Figure 9-2. Counter Summary PageRefresh Rate — Amount of time that passes before statistics are refreshed. The possible field va

392 Viewing Statisticswww.dell.com | support.dell.comFigure 9-3. Interface Statistics PageInterface — Specifies whether statistics are displayed for a

Viewing Statistics 393Packets with Errors — Amount of errors transmitted from the selected interface.Displaying Interface Statistics1Open the Interfac

394 Viewing Statisticswww.dell.com | support.dell.comg12 10 685 290 32g13 0 0 0 0g14 0 0

Viewing Statistics 395Viewing Etherlike StatisticsThe Etherlike Statistics page contains interface statistics. To open the page, click Statistics/RMON

396 Viewing Statisticswww.dell.com | support.dell.comLate Collisions — Number of late collisions received the selected interface.Excessive Collisions

Viewing Statistics 397Viewing GVRP StatisticsThe GVRP Statistics page contains device statistics for GVRP. To open the page, click Statistics/RMON→ Ta

398 Viewing Statisticswww.dell.com | support.dell.comInvalid Protocol ID — Device GVRP Invalid Protocol ID statistics.Invalid Attribute Type — Device

Viewing Statistics 399sJE : Join Empty SentsJIn : Join In SentsEmp : Empty SentsLIn : Leave In SentsLE : Leave Empty SentsLA : Leave All SentPort r

Cable, Port, and Pinout Information 49Figure 3-4. Serial Connection to SwitchAC Power Connection1Using a 5-foot (1.5 m) standard power cable with safe

400 Viewing Statisticswww.dell.com | support.dell.comViewing EAP StatisticsThe EAP Statistics page contains information about EAP packets received on

Viewing Statistics 401Invalid Frames Receive — The number of unrecognized EAPOL frames received on this port.Length Error Frames Receive — The number

402 Viewing Statisticswww.dell.com | support.dell.comThe following is an example of the CLI commands:Viewing RMON StatisticsRemote monitoring (RMON) a

Viewing Statistics 403Figure 9-7. RMON Statistics Group PageInterface — Specifies the port or LAG for which statistics are displayed.Refresh Rate — Am

404 Viewing Statisticswww.dell.com | support.dell.comBroadcast Packets Received — Number of good broadcast packets received on the interface since the

Viewing Statistics 405Broadcast: 7 Multicast: 1CRC Align Errors: 0 Collisions: 0Undersize Pkts: 0 Oversize Pkts: 0Fragments: 0 Jabbers: 0 64 Octets: 9

406 Viewing Statisticswww.dell.com | support.dell.comCurrent No. of Samples in List — Indicates the current number of samples taken.Sampling Interval

Viewing Statistics 407Console (config)# interface ethernet g8Console (config-if)# rmon collection history 1 interval 2400Console (config-if)# exitCons

408 Viewing Statisticswww.dell.com | support.dell.comReceived Packets — The number of packets received during the sampling interval.Broadcast Packets

Viewing Statistics 409The following is an example of the CLI commands for displaying RMON ethernet statistics for throughput on index 1:Console# show

4 Contents3 Cable, Port, and Pinout InformationPin Connections for the 10/100/1000 Ethernet Interface . . . . . . . . . . . 45Pin Connections for SF

50 Cable, Port, and Pinout Informationwww.dell.com | support.dell.comFigure 3-5. AC Power Connection to Switch

410 Viewing Statisticswww.dell.com | support.dell.comFigure 9-10. RMON Events Control PageEvent Entry — Indicates the event.Community — Community to w

Viewing Statistics 411Modifying a RMON Event1Open the RMON Events Control page.2Select an entry in the Event Entry field.3Modify the fields in the pag

412 Viewing Statisticswww.dell.com | support.dell.comViewing the RMON Events LogThe RMON Events Log page contains a list of RMON events. To open the p

Viewing Statistics 413Defining RMON Device AlarmsUse the RMON Alarms page to set network alarms. Network alarms occur when a network problem, or event

414 Viewing Statisticswww.dell.com | support.dell.comRising /Falling Event — The mechanism in which the alarms are reported, including a log, a trap,

Viewing Statistics 4153Select an interface.4Complete the fields in the dialog and click Apply Changes.The RMON alarm is added, and the device is updat

416 Viewing Statisticswww.dell.com | support.dell.comThe following is an example of the CLI commands:Console (config)# rmon alarm 1000 1.3.6.1.2.1.2.2

Viewing Statistics 417Figure 9-14. Port Statistics PageInterface Statistics — Selects the type of interface statistics to display.Etherlike Statistics

418 Viewing Statisticswww.dell.com | support.dell.comViewing Port Statistics Using the CLI CommandsThe following table contains the CLI commands for v

Viewing Statistics 419Viewing LAG StatisticsUse the LAG Statistics page to display statistics in a chart form for LAGs.To open the page, click Statist

Using Dell OpenManage Switch Administrator 51Using Dell OpenManage Switch AdministratorStarting the Application1Open a web browser. 2Enter the switch’

420 Viewing Statisticswww.dell.com | support.dell.comDisplaying LAG Statistics1Open the LAG Statistics page.2Select the type of statistic to display.3

Configuring Quality of Service 421Configuring Quality of ServiceThe Quality of Service page contains links to the main QoS configuration pages. To ope

422 Configuring Quality of Servicewww.dell.com | support.dell.com•Assignment to Hardware Queues — Assigns incoming packets to forwarding queues. Packe

Configuring Quality of Service 423There are two ways to apply ACLs to an interface:•Policy — In this form, ACLs are grouped together into a more compl

424 Configuring Quality of Servicewww.dell.com | support.dell.com NOTE: The DSCP values 3, 11, 19, 27, 35, 43, 51, and 59 are mapped to q1, q2 ... q8

Configuring Quality of Service 425Basic QoS ModeIn basic QoS mode, it is possible to activate one of the Trust modes, including:•VPT• DSCP•TCP•UDP•Non

426 Configuring Quality of Servicewww.dell.com | support.dell.com•Minimum Delay — The queue is assigned to a strict priority policy, and traffic is as

Configuring Quality of Service 427Selecting a Service Mode1Open the QoS Settings page.2Select a service mode in the QoS Mode field. 3Click Apply Chang

428 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-2. QOS Interface Settings Table Page

Configuring Quality of Service 429Defining QoS Settings Using the CLI CommandsThe following is an example of the CLI commands: Console(config)# qosCon

52 Using Dell OpenManage Switch Administratorwww.dell.com | support.dell.comFigure 4-1. Switch Administrator ComponentsTable 4-1 lists the interface c

430 Configuring Quality of Servicewww.dell.com | support.dell.comDefining Bandwidth SettingsUse the Bandwidth Settings page to define the bandwidth se

Configuring Quality of Service 4314Enter values for the interface’s CIR and CBS.5Click Apply Changes. The CIR and CBS for the selected interface are c

432 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-4. Port Bandwidth Settings TableShaping Type — Can be either per port, per

Configuring Quality of Service 4333Select an interface from which to copy port bandwidth settings to all or any of the interfaces listed in the Port B

434 Configuring Quality of Servicewww.dell.com | support.dell.com1 - 1252 - 1253 - 1254 - 1255 - 1256 - 1257 - 1258 - 125qid WRED thresh0 thresh1 thre

Configuring Quality of Service 435qid-weights Ef - Priority1 - 125 dis- N/A2 - 125 dis- N/A3 - 125 dis- N/A4 - 125 dis- N/A5 - N/A ena- 56 - 125 dis-

436 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-5. Global Queue SettingsThe Global Queue Settings page contains the followi

Configuring Quality of Service 437Defining CoS to Queue MappingThe CoS to Queue Mapping Table page enables mapping CoS values to specific queues. To o

438 Configuring Quality of Servicewww.dell.com | support.dell.comThe CoS to queues mapping is reset to the default, and the device is updated.Mapping

Configuring Quality of Service 4396001 26002 3 console(config)# show qos map udp-port-queueUdp port-queue map:Port queue----- -----8000 18001 2con

Using Dell OpenManage Switch Administrator 53Using the Switch Administrator ButtonsInformation Buttons2 The device view provides information about dev

440 Configuring Quality of Servicewww.dell.com | support.dell.com6 : 60 61 62 63Defining DSCP to Queue MappingThe DSCP to Queue Mapping page enables m

Configuring Quality of Service 441Mapping DSCP to Queues Using the CLI CommandsThe following is an example of the CLI commands: console(config)# qos m

442 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-8. QoS TCP to Queue PageSelect TCP Port from List — Selects a known TCP por

Configuring Quality of Service 443Removing TCP to Queue Mapping 1Open the QoS TCP to Queue page.2Click Show All to display the TCP to Queue Mapping Ta

444 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-9. UDP to Queue PageSelect UDP Port from List — Selects a known UDP port fo

Configuring Quality of Service 445Removing UDP to Queue Mapping 1Open the UDP to Queue page.2Click Show All to display the UDP to Queue Mapping Table

446 Configuring Quality of Servicewww.dell.com | support.dell.comDefining Basic QoS SettingsUse the Basic QoS Settings page to configure the Global Tr

Configuring Quality of Service 447TCP/UDP Port — Sets trust mode to TCP/UDP Port on the device. The TCP/UDP Port mapping determines the packet queue.A

448 Configuring Quality of Servicewww.dell.com | support.dell.comConsole (config)# interface ethernet g5Console (config-if) qos trustDefining QoS DSCP

Configuring Quality of Service 449Configuring DSCP Rewriting Using the CLI CommandsThe following is an example of the CLI commands to define DSCP muta

54 Using Dell OpenManage Switch Administratorwww.dell.com | support.dell.comDevice Management ButtonsDefining FieldsUser-defined fields can contain 1-

450 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-12. QoS DSCP Mapping PageDSCP In — DSCP tag on an incoming packet.Out of Pr

Configuring Quality of Service 451Configuring DSCP Mapping Using the CLI CommandsThe following is an example of the CLI commands to map DSCP values 12

452 Configuring Quality of Servicewww.dell.com | support.dell.comSetting a Tail Drop Threshold 1Open the QoS Tail Drop page.2Select a threshold for ea

Configuring Quality of Service 453Figure 10-14. QoS Class Map PageClass-Map Name — The user-defined name of the class map.IP ACL — The IP ACL from the

454 Configuring Quality of Servicewww.dell.com | support.dell.com5Select either And or Or from the Match drop-down menu if both the IP ACL and MAC ACL

Configuring Quality of Service 455console(config-cmap)# match access-group dellconsole(config-cmap)# exitconsole(config)# exitconsole> show class-m

456 Configuring Quality of Servicewww.dell.com | support.dell.comIngress Committed Burst Size (CBS) — CBS in bytes per second.Exceed Action — Action a

Configuring Quality of Service 457Defining Aggregate Policers Using the CLI CommandsThe following is an example of the CLI commands: console# qos aggr

458 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-16.QoS Policy PageSelect Policy Name — Selects a policy name.Class Map — Se

Configuring Quality of Service 459can be applied to multiple classes in the same policy map, but cannot be used across different policy maps.Single —

Using Dell OpenManage Switch Administrator 55•*•?•<•>•|Accessing the Switch Through the CLIThe switch can be managed over a direct connection to

460 Configuring Quality of Servicewww.dell.com | support.dell.com3Enter a name for the policy in the New Policy Name field.4Do one of the following:•

Configuring Quality of Service 461The following is an example of the CLI commands: console(config)# policy map policy1console(config-pmap)# class clas

462 Configuring Quality of Servicewww.dell.com | support.dell.comFigure 10-18. QoS Policy Binding PageInterface — Selects an interface.Attach Policy t

Configuring Quality of Service 4633Click Remove for each of the interfaces from which you want policies removed, and click Apply Changes.The policy is

464 Configuring Quality of Servicewww.dell.com | support.dell.com

Getting Help 465Getting HelpTechnical AssistanceIf you need assistance with a technical problem, use Dell's extensive suite of online services av

466 Getting Helpwww.dell.com | support.dell.comwww.dell.ca (Canada only)• Anonymous file transfer protocol (FTP)ftp.dell.com/Log in as user:anonymous,

Getting Help 467To contact Dell's technical support service, see "Before You Call" and then see the contact information for your region

468 Getting Helpwww.dell.com | support.dell.comBefore You CallNOTE: Have your Express Service Code ready when you call. The code helps Dell's aut

Getting Help 469Australia (Sydney)International Access Code: 0011Country Code: 61City Code: 2E-mail (Australia): [email protected] (New Z

56 Using Dell OpenManage Switch Administratorwww.dell.com | support.dell.comUsing the CLICommand Mode OverviewThe CLI is divided into command modes. E

470 Getting Helpwww.dell.com | support.dell.comBrazilInternational Access Code: 00Country Code: 55City Code: 51Website: www.dell.com/brCustomer Suppor

Getting Help 471China (Xiamen)Country Code: 86City Code: 592Tech Support website: support.ap.dell.com/chinaTech Support E-mail: [email protected]

472 Getting Helpwww.dell.com | support.dell.comDenmark (Copenhagen)International Access Code: 00Country Code: 45 Website: support.euro.dell.comE-mail

Getting Help 473France (Paris) (Montpellier)International Access Code: 00Country Code: 33City Codes: (1) (4)Website: support.euro.dell.comE-mail: supp

474 Getting Helpwww.dell.com | support.dell.comGreeceInternational Access Code: 00Country Code: 30Website: support.euro.dell.comE-mail: support.euro.d

Getting Help 475Ireland (Cherrywood)International Access Code: 16Country Code: 353City Code: 1Website: support.euro.dell.comE-mail: dell_direct_suppor

476 Getting Helpwww.dell.com | support.dell.comJapan (Kawasaki)International Access Code: 001Country Code: 81City Code: 44Website: support.jp.dell.com

Getting Help 477Latin America Customer Technical Support (Austin, Texas, U.S.A.)512 728-4093Customer Service (Austin, Texas, U.S.A.)512 728-3619Fax (T

478 Getting Helpwww.dell.com | support.dell.comNetherlands Antilles General Support001-800-882-1519Netherlands (Amsterdam)International Access Code: 0

Getting Help 479Norway (Lysaker)International Access Code: 00Country Code: 47Website: support.euro.dell.comE-mail Support (portable computers):nor_nbk

Using Dell OpenManage Switch Administrator 57To list the Privileged EXEC commands, type a question mark at the command prompt and press <Enter>.

480 Getting Helpwww.dell.com | support.dell.comSt. Lucia General Support1-800-882-1521St. Vincent and the Grenadines General Supporttoll-free: 1-877-2

Getting Help 481Sweden (Upplands Vasby)International Access Code: 00Country Code: 46City Code: 8Website: support.euro.dell.comE-mail: swe_support@dell

482 Getting Helpwww.dell.com | support.dell.comTurks and Caicos Islands General Supporttoll-free: 1-866-540-3355U.K. (Bracknell)International Access C

Getting Help 483U.S.A. (Austin, Texas)International Access Code: 011Country Code: 1Automated Order-Status Servicetoll-free: 1-800-433-9014AutoTech (po

484 Getting Helpwww.dell.com | support.dell.com

58 Using Dell OpenManage Switch Administratorwww.dell.com | support.dell.comInterface Configuration ModeInterface configuration commands modify specif

Configuring the Switch 59Configuring the SwitchThis section describes the initial device configuration. After completing all external connections, you

Contents 5Booting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Configuration Overview . . . . . . . . . . . . . . . . . . .

60 Configuring the Switchwww.dell.com | support.dell.comFigure 5-1. Installation and Configuration JobflowConnect Device and ConsolePower onPress EscS

Configuring the Switch 61General Configuration InformationYour switch has predefined features and setup configuration.Auto-NegotiationAuto-negotiation

62 Configuring the Switchwww.dell.com | support.dell.comThe following is an example for changing the port speed on port g1 using CLI commands:Console

Configuring the Switch 63Other Configuration RequirementsThe following is required for downloading embedded software and configuring the device:• ASCI

64 Configuring the Switchwww.dell.com | support.dell.comDuring boot, you can use the Startup menu, if necessary to run special procedures. To enter th

Configuring the Switch 65PowerConnect 6024Tapi Version: v1.1a1-P18Core Version: v1.1a1-P1818-May-2003 16:24:41 %INIT-I-InitCompleted: Initialization t

66 Configuring the Switchwww.dell.com | support.dell.comConfiguration OverviewYour switch supports a 10/100 Mbps Ethernet Out-of-Band (OOB) management

Configuring the Switch 67The system will prompt you with a default answer; by pressing enter, you accept the default.After you configure basic setting

68 Configuring the Switchwww.dell.com | support.dell.comPlease enter the Management System IP address(A.B.C.D) or wildcard (0.0.0.0) to manage from an

Configuring the Switch 69 NOTE: Each part of the IP address must start with a number other than zero. For example, IP addresses 001.100.192.6 and 192

6 Contents6 Configuring System InformationOpening the System Page . . . . . . . . . . . . . . . . . . . . . . . . . 99Defining General Device Inform

70 Configuring the Switchwww.dell.com | support.dell.comThe device can now be managed either from the already connected Console port or remotely throu

Configuring the Switch 71100.1.1.1/24 vlan 1 static disableOOB ip interfacesGateway IP Address Activity status---------------------

72 Configuring the Switchwww.dell.com | support.dell.comconsole# delete startup-configStartup file was deletedconsole# reloadYou haven’t saved your ch

Configuring the Switch 73Configuring an Initial Console PasswordTo configure an initial console password, enter the following commands:console(config)

74 Configuring the Switchwww.dell.com | support.dell.com• When initially logging onto a device through a SSH session, enter jones at the password prom

Configuring the Switch 75Please download program using XMODEM.console#2Specify the source file path within 20 seconds.If the path is not specified wit

76 Configuring the Switchwww.dell.com | support.dell.comconsole# show bootvarImages currently available on the Flash Image-1 active (selected for next

Configuring the Switch 77Boot Image Download Loading a new boot image from the TFTP server and programming it into the flash updates the boot image. T

78 Configuring the Switchwww.dell.com | support.dell.comThis section also describes accessing a switch for the first time with the default configurati

Configuring the Switch 79Figure 5-2. HyperTerminal Properties Window NOTE: 115,200 is the default baud rate for new device. The device may have anothe

Contents 7Running Cable Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . 166Viewing Copper Cable Diagnostics. . . . . . . . . . . . . . .

80 Configuring the Switchwww.dell.com | support.dell.comTesting CPU PCI Bus Configuration...PASS BOOT Version 1.0.0.13 Date 13-Aug-200

Configuring the Switch 81Dram second PTR is : 0xFE00000Flash size is: 16MTuning File info. Ver: 0.2.80 Creation date: Aug 20 2003 11:20:13PowerConnec

82 Configuring the Switchwww.dell.com | support.dell.comThe device is ready for configuration.Device Default SettingsTo return to device default setti

Configuring the Switch 83This example will use port g1. 3Ensure (on the ASCII terminal) that the interface status changed to “up” and that the STP sta

84 Configuring the Switchwww.dell.com | support.dell.comconsole(config)# exitconsole# ping 50.1.1.264 bytes from 50.1.1.2: icmp_seq=1. time=0 ms64 byt

Configuring the Switch 85console(config-line)# login authentication defaultconsole(config-line)# enable authentication defaultconsole(config-line)# pa

86 Configuring the Switchwww.dell.com | support.dell.comFigure 5-3. Local Area Connection Properties Window3Click Internet Protocol (TCP/IP) and then

Configuring the Switch 87Figure 5-4. Internet Protocol (TCP/IP) Properties Window4Click Use the following IP address.5Enter the appropriate addresses

88 Configuring the Switchwww.dell.com | support.dell.com3Enter the command Telnet and the device IP address, such as the following:Microsoft Windows 2

Configuring the Switch 89Enabling Web Access (HTTP Server)1To prevent problems that may occur when using an HTTP proxy server, disable (uncheck) the p

8 ContentsConfiguring Port Security . . . . . . . . . . . . . . . . . . . . . . 242Defining IP based ACLs . . . . . . . . . . . . . . . . . . . . .

90 Configuring the Switchwww.dell.com | support.dell.comFigure 5-6. Logging onto the Web InterfaceThe password authentication window is displayed.3Ent

Configuring the Switch 91Figure 5-7. Dell OpenManage Switch Administrator PageConfiguring Secure Management Access (HTTPS)When managing the device sec

92 Configuring the Switchwww.dell.com | support.dell.comFigure 5-8. Logging Onto the Web Interface With a Secure ConnectionThe Security Alert window i

Configuring the Switch 93The Startup menu is displayed and contains the following configuration functions: [1] Download Software[2] Erase Flash File[3

94 Configuring the Switchwww.dell.com | support.dell.com1From the Startup menu, press <2> within 6 seconds to erase flash file. The following me

Configuring the Switch 956Confirm by pressing <Y>.The following message is displayed:Erasing flash blocks 1 - 63: Done. Password Recovery If a p

96 Configuring the Switchwww.dell.com | support.dell.comAssigning Static IP Addresses (on an Out-of-Band Port)console>enableconsole#configureconsol

Configuring the Switch 97Additional InformationFor more information about configuring Out-of-Band, see "Configuring Out-of-Band (OOB) Management

98 Configuring the Switchwww.dell.com | support.dell.com

Configuring System Information 99Configuring System InformationOpening the System PageTo open the System page, click System in the tree view (see Figu

Contents 98 Configuring RoutingRouting Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331Configuring Global IP Routing . . . . . .

100 Configuring System Informationwww.dell.com | support.dell.comTo display the Asset page, click System→ General→ Asset in the tree view.Figure 6-2.

Configuring System Information 101Defining System Information1Open the Asset page.2Define the following fields: System Name, System Contact, System Lo

102 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# hostname dellConso

Configuring System Information 103Figure 6-3. Time SynchronizationThe Time Synchronization page contains the following fields:Clock Source — The time

104 Configuring System Informationwww.dell.com | support.dell.comEuropean — The device clock changes to DST at 1:00 am on the last Sunday in March and

Configuring System Information 105Defining Clock Settings Using CLI CommandsThe following table summarizes the equivalent CLI commands for setting fie

106 Configuring System Informationwww.dell.com | support.dell.comFigure 6-4. System HealthThe System Health page contains the following fields:Power S

Configuring System Information 107The following is an example of the CLI commands:Console# show systemSystem Description: Ethernet Routing SwitchSyste

108 Configuring System Informationwww.dell.com | support.dell.comVersion InformationThe Versions page contains information about the hardware and soft

Configuring System Information 109The following is an example of the CLI commands: Console# show versionSW version 1.0.0.67 ( date 26-Jun-2003 tim