Dell E2014T Guía de usuario

User’s Guide Dell E2014T Regulatory model: E2014Tt

10  About Your Monitor 6 7 8 9 Connect the USB cable from the monitor to the USB upstream port computer to allow you to use the USB ports and

72% (CIE1976) Color gamut (typical) NOTE: Color gamut (typical) is based on CIE1976 (72%) and CIE1931 (72%) test standards. Touch Type Infr

12  About Your Monitor Environmental Characteristics Temperature Operating 0 °C to 40 °C (32 °F to 104 °F) Non-operating -20 °C to 60 °C (-

 One USB 2.0 upstream port USB Two USB 2.0 downstream ports Audio One audio-out port Signal cable type • D-Sub • HDMI • MHL • DisplayPort •

14  About Your Monitor VESA Horizontal Vertical Video Power Indicator Power Consumption Modes Sync Sync Normal Active Active Acti

8 Pin Assignments VGA Pin 15-pin Side of the Pin 15-pin Side of the Number Connected Signal Cable Number Connected Signal Cable 1 Video-Re

16  About Your Monitor  DisplayPort Pin Number 20-pin S

Pin Signal Pin Signal Number name Number name 1 DMU 1 VCC 2 VCC 2 DMD 3 DPU 3 DPD 4 GND 4 GND NOTE: USB 2.0 functionality requires a

18  Setting Up the Monitor                                      CAUTION: Do not use benzene, thinner, a

Connecting Your Monitor WARNING: Follow the Safety Instructions before you perform any of the procedures in this section, To conn

NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage

20  Setting Up the Monitor  Connecting the USB Cable NOTE: The graphics are used for the purpose of illustration only. Appearance of the comp

To remove the stand: 1. Place the monitor on a flat surface. 2. Press and hold the Stand release button. 3. Lift the stand up and away from

22  Setting Up the Monitor 1 2 3 Operating the Monitor Side-Panel Controls Use the control buttons on the front of the monitor to adjust

1 2 3 Front-Panel Button Use the buttons on the right side of the monitor to adjust the image settings. Button Description Use the Up (inc

24  Setting Up the Monitor Using the On-Screen Display (OSD) Menu Accessing the Menu System NOTE: Any changes you make using the OSD menu

OSD Options Menu and Submenus Description Energy Use This meter shows, in real time, the energy level being consumed by the monitor. Use this m

26  Setting Up the Monitor Menu and Submenus Description Auto Adjust The Auto Adjust feature optimizes the display settings for use with your

Menu and Submenus Description Select VGA and press when your computer andVGA monitor are connecting using the VGA cable. Select DisplayPort and

28  Setting Up the Monitor Menu and Submenus Description Preset Mode Standard: Default color settings. This is the default preset mode. Mult

Menu and Submenus Description This feature adjusts the color saturation of the video image. Use or to adjust the saturation from 0 to 10

30  Setting Up the Monitor Menu and Submenus Description Dynamic Contrast adjusts the contrast ratio to 8,000,000 : 1. Dynamic Contrast Push t

Menu and Submenus Description Menu Settings Set the OSD display to one of eight languages. Language English, Espanol, Francais, Deutsch, Brazi

32  Setting Up the Monitor Menu and Submenus Description Other Settings Select this option to adjust the OSD settings, suchas the DDC/CI, LCD

Menu and Submenus Description Reset Other Settings Restores other settings, such as such as DDC/CI, to factorydefaults. Factory Reset Restores

34  Setting Up the Monitor OSD Warning Messages When the monitor does not support a display resolution, the following message appears: This mea

If you set the input to a particular mode but the cable for that mode (VGA, DP, or HDMI) is disconnected, one of the following messages appear

36  Troubleshooting Tilt With the stand, you can tilt the monitor for the most comfortable viewing angle. NOTE: The stand is detached when

or or NOTE: This message also appears during normal operation if the display cable gets disconnected or damaged. 4. Turn o your monitor a

38  Troubleshooting Built-in Diagnostics Your monitor has a built-in diagnostic tool that helps you determine if the problems with your monit

Common Problems The following table contains information about resolving common monitor problems. Common Symptoms What You Experience Possible So

40  Troubleshooting Common What You Possible SolutionsSymptoms Experience • Reset the monitor to factory settings. Brightness Picture too d

Common What You Possible SolutionsSymptoms Experience Picture color Wrong Color not good • Change the Color Setting Mode in the Color Setting

42  Troubleshooting  Touchscreen Problems Specific Symptoms Touch report error What You Experience Touch function miss alignment or no

Product Specific Problems Specific What You Possible SolutionsSymptoms Experience Screen image is too small Image is centered on screen, but d

Universal Serial Bus (USB) Specific Problems Specific What You Possible Solutions Symptoms Experience USBUSB interface peripherals are is not w

Appendix Safety Instructions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result

Setting Display Resolution to 1600x900 (maximum) For maximum display performance while using the Microsoft Windows operating s

3. Click Advanced Settings. 4. Identify your video card manufacturer (such as NVIDIA, ATI, Intel, and so on) from the description at the t

Using display settings Windows Vista 1. Right-click on the desktop and click Personalize. 2. Click Display Settings. 3. Click Identify Moni

Windows 7 1. Right-click on the desktop and click Screen resolution. 2. Click Multiple displays to choose a display selection. If you do no

About Your Monitor Package Contents Your monitor ships with the components shown below. Make sure that you have received all the components and

Windows 8 1. From the Start screen, select Desktop tile to switch to the classic Windows desktop. 2. Right-click on the desktop and click Scr

3. Click Multiple displays to choose a display selection. If you do not see the additional monitor listed, click Detect. NOTE: If your compute

Display Styles For Multiple Monitors After connecting external monitors, you can choose to duplicate, extend, or use only one of the monitors. Du

Extend displays This option shows separate content on the selected monitors. The resolution of each monitor can be set independently. You can set

Windows 8 Show desktop only on… This option allows you to select the monitor to display content. You can choose to use any one of the monitors co

Change the appearance of your displays Display. lt. Mobile PC Display ·I RHOiution: 1024 768 Orientation: landscape Connect to a proJectOr (or

!II Screen Resolutton r-1 ~~ B i' [IJ << Appelrance,tnd Pmon1lization • Display • Xfttll Resolution Change the appearance of your di

6  About Your Monitor USB cable (enables touch screen function on the monitor) Screen cleaning cloth Velcro strap • Quick Setup Guide • Dri

Features Your monitor features the following: • 49.41 cm (19.5 inch) diagonal display area. • Resolution of 1600 x 900. • Tilt adjustment (

8  About Your Monitor 1 2 Parts and Controls Front View ew Side-panel controls Label Description Function buttons (For more information, see

4 5 1 2 3 Barcode serial Refer to this label if you need to number label contact Dell for technical support. Dell soundbar Attaches the Dell S