Dell 210-ADHT Ficha de datos Pagina 2

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 6
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 1
Security
- With an OpenDNS service subscription, Dell Instant
RAPs deliver integrated web ltering, malware and
botnet protection to every device connected to the
WLAN.
- Integrated Trusted Platform Module (TPM) for secure
storage of credentials and keys.
- SecureJack-capable for secure tunneling of wired
Ethernet trac.
Operating modes
Instant AP
Controller-managed AP
Remote AP (RAP) for branch deployments
Air monitor (AM) for wireless IDS, rogue detection
and containment
Spectrum analyzer, dedicated or hybrid
Secure enterprise mesh
Wireless radio specications
AP type: Indoor, dual radio, 5GHz 802.11ac and 2.4GHz
802.11n 3x3:3
Software-congurable dual radio supports 5GHz (Radio
0) and 2.4GHz (Radio 1)
3x3 MIMO with two spatial streams and up to 1.3Gbps
wireless data rate
Supported frequency bands (country-specic
restrictions apply):
- 2.4000 to 2.4835GHz
- 5.150 to 5.250GHz
- 5.250 to 5.350GHz
- 5.470 to 5.725GHz
- 5.725 to 5.850GHz
Available channels: Dependent on congured
regulatory domain
Dynamic frequency selection (DFS) optimizes the use of
available RF spectrum
Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division
multiplexing (OFDM)
Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-
QAM
Transmit power: Congurable in increments of 0.5 dBm
Maximum (aggregate, conducted total) transmit power
(limited by local regulatory requirements):
- 2.4GHz band: +23 dBm (18 dBm per chain)
- 5GHz band: +23 dBm (18 dBm per chain)
ACC minimizes interference from cellular networks
Maximum ratio combining (MRC) for improved
receiver performance
Cyclic delay/shift diversity (CDD/CSD) for improved
downlink RF performance
Short guard interval for 20MHz, 40MHz and
80MHz channels
Space-time block coding (STBC) for increased range
and improved reception
Low-density parity check (LDPC) for high-eciency
error correction and increased throughput
Transmit beamforming (TxBF) for increased reliability in
signal delivery
Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 450 (MCS0 to MCS23)
- 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3)
802.11n high-throughput (HT) support: HT 20/40
802.11ac very high throughput (VHT) support:
VHT 20/40/80
802.11n/ac packet aggregation: A-MPDU, A-MSDU
Antennas
W-AP214/W-IAP214: Three RP-SMA connectors for
external dual band antennas. Internal loss between
radio interface and external antenna connectors (due
to diplexing circuitry): 1.0 dB in 2.4GHz and 2.0 dB in
5GHz.
W-AP215/W-IAP215: Six integrated down-tilt omni-
directional antennas for 3x3 MIMO with maximum
antenna gain of 5.0 dBi in 2.4GHz and 5.0 dBi in 5GHz.
Built-in antennas are optimized for horizontal ceiling
mounted orientation of the AP. Downtilt angle for
maximum gain is roughly 30 degrees.
Other interfaces
10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Ecient Ethernet (EEE)
- PoE-PD: 48V DC (nominal) 802.3af PoE
DC power interface, accepts 1.7/4.0 mm center-positive
circular plug with 9.5 mm length
Visual indicators (LEDs):
- Power/system status
- Ethernet link status (ENET)
- Radio status (two; RAD0, RAD1)
Reset button: factory reset (during device power up)
Serial console interface (RJ-45)
Kensington security slot
Power
Maximum (worst-case) power consumption: 14.9 watts
(PoE) or 13.6 watts (DC)
- Excludes power consumed by external USB device
(and internal overhead); this could add up to 6 watts
(PoE) or 5.5 watts (DC) for 5W/1A USB device
Maximum (worst-case) power consumption in idle
mode: 8.2 watts (PoE) or 7.4 watts (DC)
Direct DC source: 12V DC nominal, +/- 5%
Vista de pagina 1
1 2 3 4 5 6

Comentarios a estos manuales

Sin comentarios