Dell Intel PRO Family of Adapters Manual de usuario

Intel® FCoE/DCB User GuideThe information below is provided by the supplier of the referenced device and is subject to the restrictions and disclaimer

Back to Contents PageIntel® Ethernet FCoE Boot: Intel® FCoE/DCB User GuideUpgrading an FCoE-Booted SystemPreparing the Adapter for FCoE BootIntel® Eth

Intel® Ethernet 10G 4P X520/I350 rNDCIntel® Ethernet 10G 2P X540-t AdapterIntel® Ethernet 10G 4P X540/I350 rNDCTo do this:i. Go to System Setup.ii. Ch

FCoE Boot Targets Configuration MenuFCoE Boot Targets Configuration: Discover Targets is highlighted by default. If the Discover VLAN value is not wha

FCoE Target Selection MenuFrom the FCoE Target Selection menu, highlight the desired Target from the list and press Enter.From the FCoE Boot Targets C

To configure another target, select the desired target from the list or the same target with a different LUN. This process can be repeated until all d

Microsoft* Windows* Setup for Intel® FCoE BootRequirements1. Follow installation steps to install the Intel® Ethernet FCoE Boot-capable adapters with

Installing Windows Server with Local DiskAfter the Option Rom is installed, if you wish to install Windows Server 2008 or Windows Server 2012 with loc

Back to Contents PageMicrosoft* Windows* Installation and Configuration: Intel® FCoE/DCB User GuideSystem RequirementsSupported AdaptersUpgrading Wind

Microsoft HotfixesThe following Microsoft hotfixes have been found to be needed for specific use cases:All Windows Server 2008 (R1 and R2)KB983554 - H

Starting NUMA Node. This setting specifies the NUMA node on which the first FCoE queue is allocated.NUMA Node Count. This setting specifies the total

Export RegulationsCustomer acknowledges that these Products, which may include technology and software, are subject to the customs and export control

Through the network adapter properties Data Center tab.Fabric View TabThe Fabric View tab displays FC fabrics, VN2VN fabrics, physical ports, targets,

VLAN TabVLAN IDs are obtained through FIP VLAN discovery. This is a read-only page.Virtual Ports TabA list of the Virtual Ports associated with the HB

LUN and Boot Order fields are disabled and cleared when target is set to None Selected.Intel Ethernet® FCoE Boot cannot be enabled on an adapter that

A non-operational status is most likely to occur when Use Switch Settings is selected or Using Advanced Settings is active. This is generally a result

Back to Contents PageDetailed Instructions for Installing Microsoft* Windows* Server: Intel® FCoE/DCB User GuideRequirementsDetailed Instructions for

Intel® Gigabit 2P I350-t AdapterIntel® Gigabit 4P I350-t AdapterIntel® Gigabit 4P I350-t rNDCIntel® Gigabit 4P I350 bNDCIntel® Gigabit 2P I350 LOM3. C

10. As administrator: Open a command window. Navigate to Intel® Ethernet drivers “\FCOEBOOT\Win32” or “\FCOEBOOT\Winx64” depending on installed OS. Ru

the drive selection screen, input SHIFT-F10 to open a command prompt.Important: At the command prompt, cycle through the drive letters and use the di

3. Create partition primary SIZE=100.4. Select partition 1.5. Active.6. Format FS=NTFS QUICK.7. Assign LETTER=E.8. Create partition primary.NOTE: Add

Back to Contents PageLinux Installation on Intel® Fibre Channel Over Ethernet (FCoE): Intel® FCoE/DCB User GuideSLES 11 FCoE InstallationRHEL 6.0 FCoE

Back to Contents PageOverview: Intel® FCoE/DCB User GuideFCoE VN to VN SupportInstallation OverviewFCoE Infrastructure - Installation and Configuratio

Configuring Link Layer Discovery Protocol agent daemon (lldpad)lldpad is a utility used to initiate and configure the Link Layer Discovery Protocol (L

Configuring Intel® Ethernet FCoE1. Create a configuration file for the VLAN interface. To copy cfg file, run command:NOTE: The sample file is cfg-ethx

5. Verify that you have been assigned on a storage target.root# fcoeadm -t Interface: eth3.100-fcoe ... FC-ID (Port ID): 0x4A06EF State: OnlineLUN ID

show statistics: fcoeadm -sroot# fcoeadm -s eth3.100-fcoe 1 eth3.100-fcoe interval: 1 Err Inv IvTx Link Cntl Input Input Output Output Seconds TxFrame

Back to Contents PageIntel® Ethernet FCoE Linux Management Tools Installation Guide: Intel® FCoE/DCB User GuideRequirementsfcoeadmfcoemonThe Intel® Et

specified, the default interval is one second.-v, -version Displays the version of the fcoeadm command.-h, -helpDisplays the usage message of the fco

fcoemonThe fcoemon command is an FCoE management tool provided by the Open-FCoE package.fcoemon is the daemon of the fcoe system service. When fcoemon

Criteria of Creating, Resetting and Destroying FCoE InterfaceIn this section the dcbtool is used to describe the conditions of the DCB feature status

This is the common configuration file for the fcoe system service. This file will be read by the /etc/init.d/fcoe script, the etc/fcoe/scripts/fcoeplu

Back to Contents PageData Center Bridging (DCB) for Intel® Network Connections: Intel® FCoE/DCB User GuideOverviewDCB for WindowsDCB for LinuxOverview

What is VN to VN?FCoE VN to VN (VN2VN) support is a new proposal standard by T11 for connecting two end-nodes (ENodes) directly using FCoE. An ENode c

A non-operational status is most likely to occur when Use Switch Settings is selected. This is generally a result of one or more of the DCB features n

In an effort to address these issues, Intel and a host of industry leaders have been working on addressing these problems. Specifically, within the IE

Optionslldpad has the following command line options: -h show usage information -f configfile: use the specified file as the config file instead of

# tc filter add dev ethX protocol ip parent 1: \ u32 match ip sport 5000 0xffff action skbedit queue_mapping 0# tc filter add dev ethX protocol ip par

license Displays dcbtool license information.quit exit from interactive mode.The following commands interact with the lldpad daemon to manage the dae-

pgpct:x,x,x,x,x,x,x,x percentage of link bandwidth allocated to the corresponding Priority Group. The total bandwidth must equal 100%.uppct:x,x,x,x,x

A TX unit hang may be observed when link strict priority is set when a large amount of traffic is transmitted on the link strict priority.Licensedcbd

Back to Contents PageKnown Issues: Intel® FCoE/DCB User GuideWindows IssuesFCoE Boot IssuesWindows IssuesIntel® Ethernet Virtual Storage Miniport Driv

Microsoft article 278431.ANS teaming will work when NLB is in multicast mode, as well. For proper configuration of the adapter in this mode, refer to

restarted to indicate to the OS that the port is a boot port. When the user then adds the Hyper V service to the system, the OS takes a snap shot of

MultiPoint ModeIf more than two ENodes are detected in the VN2VN fabric, then all nodes should operate in Multipoint mode:Installation OverviewFor inf

Back to Contents PageSupport: Intel® FCoE/DCB User GuideWeb and Internet Siteshttp://www.support.dell.comCustomer Support TechniciansIf the troublesho

Back to Contents PageGlossary: Intel® FCoE/DCB User GuideThis Glossary defines terms, abbreviations, and acronyms that apply directly to Intel® Ethern

PDU Protocol Data UnitPFC Priority Flow ControlRaw Packet DriverStandard Ethernet MAC driver.RDMA Remote Direct Memory AccessRDMAC RDMA ConsortiumRSSR

Intel® Ethernet Flash Firmware UtilityOverviewRunning BootUtilCommand Line ParametersExamplesDOS Exit CodesOverviewThe Intel® Ethernet Flash Firmware

BootUtil is located on the software installation CD in the \BOOTUTIL directory. Always check the Dell Customer Support website (http://www.support.del

-O=[FILENAME]Redirects all text output to the specified filename. It must be used with the -E or -NIC option. If used with the -E option, a list of al

Intel® Gigabit ET Quad Port Mezzanine CardIntel® Gigabit 4P I350-t MezzIntel® Ethernet X520 10GbE Dual Port KX4 MezzIntel® Ethernet X520 10GbE Dual Po

WWNNPREFIX=10-00.-SHOWFCOEDisplays the FCoE Target Configurations for the selected NIC.FCoE Target Configuration OptionsDescription-[OPTION]=[VALUE]Th

Example 4:To disable the firmware on the second network port in the system:BootUtil -NIC=2 -BOOTENABLE=DISABLEDNOTE: This command will work only on an

Dell Update Package for Intel Adapter Firmware The Dell Update Package (DUP) for Intel Adapter Firmware is provided by Dell. It includes all support f

Back to Contents PageSystem Requirements: Intel® FCoE/DCB User GuideBefore installing Intel® Server Adapters and Intel® Ethernet FCoE Protocol Driver,

Back to Contents PageSoftware License Agreement: Intel® Network Adapters User GuideINTEL SOFTWARE LICENSE AGREEMENT (Final, License)IMPORTANT - READ B

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS PROHIBIT EXCLUSION OR LIMITATION OF LIABILITY FOR IMPLIED WARRANTIES OR CONSEQUENTIAL

Microsoft* Windows* Server 2008 (with latest service pack and Hyper-V role) - Standard, DataCenter, or EnterpriseMicrosoft Windows Server 2008 CoreSup

Back to Contents PageSwitch Configuration for Intel® Ethernet FCoE Protocol Driver: Intel® FCoE/DCB User GuideNexus/Cisco Switch PlatformBrocade Switc

Back to Contents PageInstallation and Setup: Intel® FCoE/DCB User GuideThis section provides information for installing and setting up Intel® FCoE com