Dell PowerVault NX3500 Manual de usuario descargar pdf (Pagina 2)

Setting Up Your PowerVault Network Attached Storage Solution

(continued)

Title

Description

Getting Started Guide

The Getting Started Guide provides an

overview of system features, setting up your

solution, and technical speciﬁ cations.

This document is shipped with your system

and is also available at support.dell.com/

manuals.

Hardware Owner’s Manual

The Hardware Owner’s Manual provides

information about solution features and

describes how to troubleshoot the system

and install or replace system components.

This document is available at support.dell.

com/manuals.

Rack Installation Instructions

The rack documentation included with your

rack solution describes how to install your

system into a rack. This document is shipped

with your rack solution and is also available

at support.dell.com/manuals.

Administrator’s Guide

The Administrator’s Guide provides

information about conﬁ guring, managing,

and troubleshooting the software and the

solution. This document is available at

support.dell.com/manuals.

Online Help

The Online Help provides information about

conﬁ guring and managing the software.

The online help is integrated with the system

and can be accessed from the PowerVault

NX3500 web interface.

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written

permission of Dell Inc. is strictly prohibited.

Dell™, the DELL

logo, and PowerVault™ are trademarks of Dell Inc.

Other trademarks and trade names may be used in this publication to refer to either

the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Printed in the U.S.A.

2011 - 08

4 | Preparing Your Environment for the PowerVault NX3500 Solution

IP Chart

The IP chart helps you plan your conﬁ guration. Recording the IP addresses of your solution in a single location enables you to conﬁ gure your setup faster and more eﬃ ciently.

PowerVault MD Conﬁ guration

IP Function IPs Allocated Sample IPs Physical

Connections

Controller 0 Port 0 IP

. . .

192.168.10.100 SAN (to

switch A)

Controller 0 Port 1 IP

. . .

192.168.11.100 SAN (to

switch B)

Controller 0 Port 2 IP

. . .

192.168.12.100

Controller 0 Port 3 IP

. . .

192.168.13.100

Controller 1 Port 0 IP

. . .

192.168.10.101 SAN (to

switch A)

Controller 1 Port 1 IP

. . .

192.168.11.101 SAN (to

switch B)

Controller 1 Port 2 IP

. . .

192.168.12.101

Controller 1 Port 3 IP

. . .

192.168.13.101

Terms Used In the IP Chart

Controller—A server appliance installed with the Dell scalable ﬁ le system software. An

essential component of a PowerVault NAS clustered solution.

Internal IP—IP address used for internal operations between the NAS controllers and the

storage subsystem.

SAN network/iSCSI network—The network that carries the block level (iSCSI) traﬃ c and

to which the storage subsystem is connected. It is recommended that this network be

separated from the client network.

NAS cluster name—The name that is used to identify the PowerVault NX3500

solution.

NAS management VIP—IP addresses that the management stations use to access the

PowerVault NX3500 controllers.

Client access VIP—IP address that clients use to access CIFS shares and NFS exports

hosted by a PowerVault NAS solution. The PowerVault NAS solution supports multiple

client access VIPs.

MD discovery IP—The MD discovery IP is an MD storage array (iSCSI) IP address from

either the SAN A or SAN B network.

Preparing the Management Station

Connect the management station to the client switch.•

Verify that IPv6 is enabled.•

Verify that Java (JRE) is installed on the management station.•

Install the • PowerVault Conﬁ guration Utility software.

Download SSH client for CLI access.•

Preparing the Modular Disk Storage Arrays

Create a disk group for each virtual disk.1.

Create a virtual disk in each disk group. Virtual disks must be created and assigned 2.

to the host group in pairs. A minimum of 2 virtual disks is required and a maximum

of sixteen is supported. Each pair of virtual disks must be of the same size. For more

information, see the

Administrator’s Guide

Create a host group. For example, name host group 3.

PV-NX3500

Map the virtual disks to the host group.4.

NOTE: Additional conﬁ guration is required after completing the steps in the

PowerVault Conﬁ guration Utility. For more information, see step 5.

5 | Conﬁ guration Utility and Modular Disk Storage Manager Client

NAS Appliance Setup Worksheet

PowerVault NAS Conﬁ guration

Utility Conﬁ guration

NAS Cluster IP Allocation

Info Requested Value IP Function IPs Allocated Sample IPs Physical

Connections

Storage Array Identiﬁ cation Subnet 1 - Primary Network

MD Discovery IP

. . .

Client Access VIP

. . .

10.10.1.100 Client

MTU NAS Management VIP

. . .

10.10.1.200 Client

NX3500 Controller Discovery Controller 0 IP

. . .

10.10.1.201 Client

Controller 0 MAC Address Controller 1 P

. . .

10.10.1.202 Client

Controller 1 MAC Address Subnet Mask

. . .

255.255.255.0 Client

Gateway

. . .

10.10.1.1 Client

NAS Appliance Identiﬁ cation

NAS Cluster Name Subnet 2 - Internal/Private Network Group 1

Internal IP a0

. . .

172.168.1.1 Internal/Peer

PowerVault NAS Conﬁ guration

Utility Results

Internal IP a1

. . .

172.168.1.2 Internal/Peer

NAS Controller 0 IQN Internal IP a2

. . .

172.168.1.3 Internal/Peer

NAS Controller 1 IQN Internal IP a3

. . .

172.168.1.4 Internal/Peer

Use the IQNs recorded from the PowerVault

NAS Conﬁ guration Utility to complete your

mappings conﬁ guration on the MD3x00i

backend storage

Subnet Mask

. . .

255.255.255.0 Internal/Peer

NAS Appliance Setup Worksheet - continued

Environment Setup Checklist NAS Cluster IP Allocation

Management Station

Verify IPv6 enabled•

Install PowerVault NAS Conﬁ guration Utility•

Switch Topology

Determine desired switch topology from one

of the following conﬁ gurations:

All-in-one•

All-in-one high availability•

Optimal•

Optimal high availability•

IP Function IPs Allocated Sample IPs Physical

Connections

Subnet 3 - Internal/Private Network Group 2

Internal IP b0

. . .

172.168.2.1 Internal/Peer

Internal IP b1

. . .

172.168.2.2 Internal/Peer

Internal IP b2

. . .

172.168.2.3 Internal/Peer

Internal IP b3

. . .

172.168.2.4 Internal/Peer

Subnet Mask

. . .

255.255.255.0 Internal/Peer

Subnet 4 - SAN Network Group 1

SANa IP 0

. . .

192.168.10.20 SAN (to

Switch A)

SANa IP 1

. . .

192.168.10.21 SAN (to

switch A)

Subnet Mask

. . .

255.255.255.0

Subnet 5 - SAN Network Group 2

SANb IP 0

. . .

192.168.11.20 SAN (to

switch B)

SANb IP 1

. . .

192.168.11.21 SAN (to

switch B)

Subnet Mask

. . .

255.255.255.0

Launching the Conﬁ guration Wizard

From the management station, launch the PowerVault

Conﬁ guration Utility and follow the instructions on the

screen.

The PowerVault Conﬁ guration Utility guides you through

the network conﬁ guration and enables you to set up and

access the PowerVault NX3500 controllers on the

management station.

Completing Your Setup

Copy the IQN numbers from the 1. Conﬁ gurations

Results screen without closing the screen.

Launch the 2. Modular Disk Storage Manager Client and

click the Mappings tab.

In the 3. Mappings screen, right-click the host group

and select Deﬁ ne→ Host. Enter a host name and click

Next.

For example,

PV-NX3500-Controller-0

4. On the second screen, type the IQN for the controller

and provide a user label. The user label must not be

the same as the host name. It is recommended that

you use the host name appended with -IQN.

For example,

PV-NX3500-Controller-0-IQN

Repeat step 3 and step 4 for controller 1.5.

Close the 6. Modular Disk Storage Manager Client.

In the 7. Conﬁ guration Results screen, click Finish.

6 | System Conﬁ guration 7 | Documentation

The PowerVault NX3500 web interface provides

information about the controller and guides you

through the steps necessary to conﬁ gure the network

for your clustered NAS solution. The web interface

automatically launches after you complete the

PowerVault Conﬁ guration Wizard.

NOTE: If your web browser does not display the

PowerVault NX3500 web interface, check the security

settings of the web browser, accept the security

certiﬁ cate, and ensure that JavaScript is enabled.

To access the PowerVault NX3500 web interface at a

later time, type the following URL in your web browser

https://<NAS Management VIP>.

Default User Name and Password

The default user name for the solution is admin

The default password for the solution is Stor@ge!

To complete the system conﬁ guration, complete the

following steps in the PowerVault NX3500 web interface:

Configuring DNS •

Configuring time •

Configuring e-mail •

Configuring SNMP•

Setting up file system•

Changing the administrator password•

Configuring system identity•

Configuring identity management•

Configuring cross protocol •

Creating NAS volumes•

Creating CIFS shares•

Creating NFS exports•

1 2

1
1
1
(continued) 2

Comentarios a estos manuales

Sin comentarios

Dell PowerVault NX3500 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware De La Computadora Dell PowerVault NX3500