Dell OpenManage Server Administrator Version 7.4 Manual de usuario Pagina 68
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
name=value pair 1 attribute= name=value pair 2 setting= Description
NOTE: On Linux systems,
user or user groups
upgraded to administrator or
administrator groups cannot
configure this BIOS setup
setting.
attribute=cstates setting=enabled | disabled
• enabled: Enables the
processor to go into a deep
sleep state when the system is
not utilized.
• disabled: Disables the
processor to go into a deep
sleep state when the system is
not utilized.
attribute=conredirect setting=enabled | disabled
• enabled: Redirects the BIOS
screen output over serial port
1. Keyboard and text output
are redirected over serial port
2.
• disabled: Turns off the BIOS
console redirection.
attribute=crab setting=enabled | disabled
• enabled: Enables BIOS
console redirection after
system reboot.
• disabled: Disables BIOS
console redirection.
NOTE: The attribute crab is
valid for Dell PowerEdge 9G
systems only.
attribute=cpucle setting=enabled | disabled
• enabled: Enables processor
C1-E after system reboot.
• disabled: Disables processor
C1-E after system reboot.
attribute=cpuht setting=enabled | disabled
• enabled: Enables logical
processor hyperthreading.
• disabled: Disables logical
processor hyperthreading.
attribute=cpuvt setting=enabled | disabled
• enabled: Enables
virtualization.
• disabled: Disables
virtualization.
attribute=cpuxdsupport setting=enabled | disabled
• enabled: Enables Execute
Disable (XD) support on the
system.
68
- Notes, Cautions, and Warnings 2
- Contents 3
- Introduction 11
- Commands 13
- Primary CLI Commands 13
- Success Messages 14
- Failure Messages 14
- Command Syntax Overview 15
- Using The omhelp Command 17
- Table 2. Optional Parameters 18
- The Instrumentation Service 19
- Hwperformance 31
- Omreport Chassis Intrusion 32
- Pwrmanagement 39
- Removableflashmedia 43
- Omreport Licenses 45
- Servermodule Commands 45
- Commands For Viewing Logs 46
- Operatingsystem 50
- Omreport Preferences Commands 58
- Omconfig About 65
- Default Warning Thresholds 90
- Usage Of Dracusergroup=custom 98
- Omconfig Preferences 101
- Omconfig Preferences Messages 102
- Defining Alert Actions 103
- Available Alert Actions 104
- Example Current Probe Actions 106
- Example Fan Probe Actions 106
- Commands For Clearing Logs 107
- Platformevents 108
- Severity 111
- Example Recovery Commands 113
- Thrmshutdown 114
- Adding Lease Information 121
- Adding Outsource Information 123
- Adding Owner Information 124
- Adding Support Information 125
- Adding System Information 126
- Adding Warranty Information 127
- CLI Command Syntax 129
- Syntax Of Command Elements 130
- Omreport Storage Commands 133
- Omreport Physical Disk Status 134
- Omreport Controller Status 135
- Omreport Enclosure Status 135
- Omreport Fan Status 136
- Omreport Power Supply Status 137
- Omreport EMM Status 138
- Omreport Battery Status 139
- Omreport Global Information 139
- Omreport Connector Status 140
- Omreport Cachecade Status 140
- Omreport PCIe SSD Status 140
- Omreport Fluid Cache Status 141
- Omreport Storage Tape 142
- Omconfig Storage Commands 143
- Omconfig Blink Physical Disk 144
- Omconfig Online Physical Disk 148
- Omconfig Clear Physical Disk 150
- Omconfig Check Consistency 154
- Omconfig Blink Virtual Disk 156
- Omconfig Unblink Virtual Disk 156
- Omconfig Delete Virtual Disk 158
- Omconfig Format Virtual Disk 159
- Omconfig Secure Virtual Disk 160
- Omconfig Rename Virtual Disk 161
- Omconfig Controller Commands 163
- Omconfig Rescan Controller 165
- Table 93. Size Parameter 169
- Controller=id 170
- Table 99. Size Parameter 171
- Cachepolicy=<d 172
- Omconfig Set Reconstruct Rate 175
- Omconfig Set Patrol Read Mode 178
- Omconfig Start Patrol Read 178
- Omconfig Stop Patrol Read 178
- Omconfig Create Cachecade 179
- Omconfig Rekey LKM Controller 179
- Omconfig Enclosure Commands 180
- Omconfig Blink 183
- Omconfig Battery Commands 184
- Omconfig Global Commands 184
- Omconfig Connector Commands 186
- Omconfig Cachecade Commands 187
- Omconfig Delete Cachecade 188
- Omconfig Resize Cachecade 188
- Omconfig Rename Cachecade 188
- Omconfig PCIe SSD Commands 189
- Omconfig Fluid Cache Commands 190
- Omconfig Partition Command 190
- List (lst) 196
- Table (tbl) 197
- Custom Delimited Format (cdv) 198
Relacionado con productos y manuales para Servidores Dell OpenManage Server Administrator Version 7.4
Servidores Dell PowerEdge 2650 Manual de usuario
(43 paginas)
(43 paginas)
Servidores Dell Microsoft Windows Compute Cluster Server 2003 Service Pack 1 Manual de instalación
(20 paginas)
(20 paginas)
Servidores Dell PowerEdge R910 El manual del propietario
(210 paginas)
(210 paginas)
Servidores Dell PowerEdge R815 Guía de inicio rápido
(50 paginas)
(50 paginas)
Servidores Dell PowerEdge T710 Guía de inicio rápido
(50 paginas)
(50 paginas)
Servidores Dell R2 Manual de usuario
(103 paginas)
(103 paginas)
Servidores Dell PowerEdge R810 Guía de inicio rápido
(60 paginas)
(60 paginas)
Servidores Dell Lifecycle Controller 1.5 Notas
(8 paginas)
(8 paginas)
Servidores Dell PowerEdge 2970 El manual del propietario
(188 paginas)
(188 paginas)
Servidores Dell PowerEdge M605 El manual del propietario
(236 paginas)
(236 paginas)
Servidores Dell PowerEdge 6950 El manual del propietario
(166 paginas)
(166 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales