Dell PowerEdge M IO Aggregator El manual del propietario Pagina 182
- Pagina / 258
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
180 | Link Aggregation Control Protocol (LACP)
www.dell.com | support.dell.com
debug lacp
Debug LACP (events).
Syntax
debug lacp [events | pdu interface [in | out]]
To disable LACP debugging, use the no debug lacp [events | pdu interface [in | out]] command.
Parameters
Defaults
none
Command Modes
EXEC
EXEC Privilege
Command
History
show lacp
Displays the LACP matrix.
Syntax
show lacp port-channel-number [sys-id | counters]
Parameters
Command Modes
EXEC
EXEC Privilege
Command
History
events (OPTIONAL) Enter the keyword events to debug LACP event information.
pdu in | out (OPTIONAL) Enter the keyword pdu to debug LACP Protocol Data Unit
information. Optionally, enter an
in or out parameter to:
• Receive enter
in
• Transmit enter out
interface in | out
Enter the following keywords and slot/port or number information:
• For a Ten Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
followed by the slot/port information.
Version 8.3.17.0 Supported on M I/O Aggregator
port-channel-number
Enter a port-channel number:
Range: 1 to 128
sys-id (OPTIONAL) Enter the keyword sys-id and the value that identifies a
system.
counters (OPTIONAL) Enter the keyword counters to display the LACP counters.
Version 8.3.17.0 Supported on M I/O Aggregator
- Notes, Cautions, and Warnings 2
- About this Guide 7
- Related Documents 8
- Before You Start 9
- DCB Support 10
- FCoE Connectivity 10
- Link Aggregation 11
- Link Tracking 11
- Where to Go From Here 12
- Before You Start 13
- 12 14
- CLI Basics 15
- Multiple Configuration Users 16
- Obtaining Help 17
- Combination Action 18
- Using the Keyword no 19
- Filtering show Commands 19
- Command Modes 20
- INTERFACE Mode 21
- LINE Mode 21
- MONITOR SESSION Mode 21
- PROTOCOL LLDP Mode 22
- File Management 23
- 27
- url url 30
- 36 38
- Control and Monitoring 39
- FTOS#configure 40
- FTOS(conf)# 40
- 54 56
- FTOS#show memory stack-unit 0 57
- Control and Monitoring 59
- Important Points to Remember 62
- Control and Monitoring 65
- [stack-unit unit-id 68
- Control and Monitoring 69
- Examples 69
- system component status 71
- 76 78
- BOOT_USER # 80
- 86 88
- Data Center Bridging 89
- 90 92
- Data Center Bridging 93
- FTOS# show dcb 95
- DCB Status : Enabled 95
- 96 98
- Data Center Bridging 99
- Field Description 100
- EXEC Privilege 101
- 104 106
- Overview 107
- DHCP Client Commands 107
- FIP Snooping 113
- FTOS#show fip-snooping config 114
- Global FC-MAP Value: 0X0EFC00 114
- FTOS# show fip-snooping enode 115
- FTOS# show fip-snooping fcf 116
- FIP Snooping 119
- IGMP Commands 121
- TenGigabitEthernet 124
- Interfaces 127
- Port Channel Commands 128
- Virtual LAN (VLAN) Commands 129
- FTOS(conf-po-failover-grp)# 132
- FTOS(conf)#int vlan 3 136
- FTOS(conf-if-vl-3)# 136
- FTOS(conf-lldp)#show conf 142
- FTOS(conf-lldp)# 142
- Line Description 144
- [interface] description 146
- FTOS#show int po 1 brief 149
- Codes: L - LACP Port-channel 149
- unit-id ] 151
- Items Description 152
- OK Status: Terminated 153
- G = GVRP VLAN 154
- P = primary VLAN 154
- C = community VLAN 154
- I = isolated VLAN 154
- Column Heading Description 155
- 158 160
- IPv4 Routing 161
- Lines Description 170
- • too short 174
- 174 176
- 178 180
- LACP Commands 181
- Layer 2 185
- 186 188
- LLDP Commands 189
- Port Monitoring 193
- Port Monitoring 197
- Commands 197
- FTOS(conf-mon-sess-11)# 198
- Quality of Service (QoS) 199
- Security 201
- port-number 206
- {1 206
- 206 208
- SNMP Commands 209
- Syslog Commands 209
- [facility-type] 212
- CONFIGURATION 212
- Example 1 217
- Example 2 217
- Disabled 219
- Stacking Commands 221
- 0-5 hard 222
- [stack 226
- Storm Control 227
- Storm-Control Enabled 228
- System Time 229
- FTOS#show calendar 230
- Enter one of the following: 235
- 234 236
- UFD Commands 237
- Debugging and Diagnostics 241
- Example 3 246
- 0-0 [port 248
- 0-0 {counters 248
- Example 4 249
- Example 250
- Example 7 251
- Example 8 251
- 0-5 port-set 0-0 [counters] 253
- Message Types 257
Relacionado con productos y manuales para Servidores Dell PowerEdge M IO Aggregator
Servidores Dell External OEMR R510 Manual de usuario
(25 paginas)
(25 paginas)
Servidores Dell PowerEdge R200 El manual del propietario
(182 paginas)
(182 paginas)
Servidores Dell PowerEdge R610 El manual del propietario
(184 paginas)
(184 paginas)
Servidores Dell EMC AX4-5I Manual de usuario
(5 paginas)
(5 paginas)
Servidores Dell 1955 Manual de usuario
(12 paginas)
(12 paginas)
Servidores Dell 8/8 Información técnica
(147 paginas)
(147 paginas)
Servidores Dell PowerEdge NM176 Guía de usuario
(292 paginas)
(292 paginas)
Servidores Dell PowerEdge VRTX El manual del propietario
(150 paginas)
(150 paginas)
Servidores Dell 800 Manual de servicio
(75 paginas)
(75 paginas)
Servidores Dell POWEREDGE R710 Especificaciones
(63 paginas)
(63 paginas)
Servidores Dell DAE Manual de usuario
(16 paginas)
(16 paginas)
Servidores Dell PowerVault 3000i Manual de usuario
(14 paginas)
(14 paginas)
Servidores Dell PowerEdge FE600W Manual de usuario
(34 paginas)
(34 paginas)
Servidores Dell PowerVault 3000i Especificaciones
(32 paginas)
(32 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales