Dell Networking S6000 Guía de usuario Pagina 87
- Pagina / 151
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Related
Commands
enable password — configures a password for the enable command and to
access a privilege level.
enable optic-info-update interval
Enable polling intervals of optical information updates for simple network management protocol (SNMP).
S6000
Syntax
enable optical-info-update interval seconds
To disable optical power information updates, use the no enable optical-
info-update interval command.
Parameters
interval
seconds
Enter the keyword interval then the polling interval in
seconds. The range is from 120 to 6000 seconds. The
default is
300 seconds (5 minutes).
Defaults Disabled
Command
Modes
CONFIGURATION
Command
History
This guide is platform-specific. For command information about other platforms,
refer to the relevant Dell Networking OS Command Line Reference Guide.
The following is a list of the Dell Networking OS version history for this command.
Version 9.0.2.0 Introduced on the S6000.
Version
8.3.19.0
Replacement command for the S4820T. Replaces the
enable xfp-power-updates command.
Version 8.3.11.4 Replacement command for the Z9000. Replaces the enable
xfp-power-updates
command
Version
8.3.10.0
Replacement command for the S4810 only. Replaces the
enable xfp-power-updates command.
Usage
Information
To enable polling and to configure the polling frequency, use this command.
Control and Monitoring
87
- S6000 System 1
- 9.5(0.1) 1
- Notes, Cautions, and Warnings 2
- Contents 3
- About this Guide 37
- Information Icons 38
- CLI Basics 39
- Obtaining Help 40
- Navigating the CLI 42
- Using the Keyword no Command 42
- Filtering show Commands 42
- Displaying All Output 43
- Command Modes 45
- CONTROL-PLANE Mode 46
- DHCP Mode 46
- DHCP POOL Mode 46
- ECMP GROUP Mode 46
- EIS Mode 46
- EXEC Mode 47
- EXEC Privilege Mode 47
- EXTENDED COMMUNITY LIST Mode 47
- FRRP Mode 47
- INTERFACE Mode 47
- IP ACCESS LIST Mode 48
- ISIS ADDRESS-FAMILY Mode 48
- LLDP Mode 49
- LINE Mode 49
- MAC ACCESS LIST Mode 49
- MONITOR SESSION Mode 49
- OPENFLOW INSTANCE Mode 50
- PREFIX-LIST Mode 51
- PROTOCOL GVRP Mode 51
- ROUTE-MAP Mode 51
- ROUTER BGP Mode 51
- ROUTER ISIS Mode 52
- ROUTER OSPF Mode 52
- ROUTER OSPFV3 Mode 52
- ROUTER RIP Mode 52
- SPANNING TREE Mode 53
- TRACE-LIST Mode 53
- VLT DOMAIN Mode 53
- VRRP Mode 53
- File Management 54
- HTTP Copy via CLI 55
- Control and Monitoring 100
- Access Control Lists (ACL) 169
- Common IP ACL Commands 171
- Standard IP ACL Commands 177
- Extended IP ACL Commands 185
- Standard MAC ACL Commands 214
- Extended MAC ACL Commands 220
- IP Prefix List Commands 226
- Route Map Commands 233
- Boot Command Line Interface 310
- NVRAM erase 317
- Border Gateway Protocol 323
- MBGP Commands 432
- CAM Profile Commands 435
- Control Plane Policing (CoPP) 445
- Data Center Bridging (DCB) 452
- PFC Commands 453
- ETS Commands 465
- DCBX Commands 472
- Polling and History) 491
- Debugging and Diagnostics 502
- Offline Diagnostic Commands 506
- Hardware Commands 509
- Commands to Configure DNS 548
- Equal Cost Multi-Path (ECMP) 553
- Introduced on the S4810 560
- Version 560
- 8.3.10.0 560
- FCoE Transit 566
- MXL Switch 572
- 8.3.12.0 581
- GARP VLAN Registration (GVRP) 593
- ICMP Message Types 605
- IGMP Commands 607
- IGMP Snooping Commands 623
- Interfaces 631
- Port Channel Commands 691
- IPv4 Routing 705
- IPv6 Basics 776
- System (IS-IS) 790
- MAC Addressing Commands 865
- Virtual LAN (VLAN) Commands 878
- LLPD Commands 899
- LLDP-MED Commands 910
- NLB Unicast Mode Scenario 921
- NLB Multicast Mode Scenario 922
- Multicast 958
- OSPFv2 Commands 966
- Policy-based Routing (PBR) 1048
- PIM-Sparse Mode (PIM-SM) 1058
- Port Monitoring 1078
- Private VLAN (PVLAN) 1086
- Quality of Service (QoS) 1108
- Per-Port QoS Commands 1112
- Policy-Based QoS Commands 1116
- DSCP Color Map Commands 1159
- Remote Monitoring (RMON) 1192
- Security 1223
- RADIUS Commands 1252
- TACACS+ Commands 1262
- Important Points to Remember 1270
- SSH Server and SCP Commands 1283
- Secure DHCP Commands 1304
- Service Provider Bridging 1316
- (SNMP) and Syslog 1335
- Syslog Commands 1361
- SNMP Traps 1383
- Storm Control 1388
- Spanning Tree Protocol (STP) 1398
- System Time and Date 1413
- Tunneling 1429
- VLAN Stacking 1438
- S6000 MXL Switch 1450
- VLT Proxy Gateway 1457
- Virtual Link Trunking (VLT) 1463
- IPv4 VRRP Commands 1496
Relacionado con productos y manuales para Software Dell Networking S6000
Software Dell PowerConnect B-DCX-4s Guía de usuario
(262 paginas)
(262 paginas)
Software Dell Force10 Z9000 Manual de usuario
(601 paginas)
(601 paginas)
Software Dell Networking S6000 Manual de usuario
(986 paginas)
(986 paginas)
Software Dell A02 Guía de usuario
(38 paginas)
(38 paginas)
Software Dell Vizioncore Guía de usuario
(189 paginas)
(189 paginas)
Software Dell V1.2 Manual de usuario
(224 paginas)
(224 paginas)
Software Dell Vizioncore Guía de usuario
(23 paginas)
(23 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales