Dell OpenManage Server Administrator Version 6.5 Manual de usuario Pagina 215
- Pagina / 282
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
omconfig storage Commands 215
See the Dell OpenManage Online Help for more information about the
controller-specific diskcache, read, write, and cache policy. For information
on specifying these parameters using the omconfig command, see the
following:
•
[readpolicy=<ra| nra| ara| rc| nrc>]
Parameter (Optional)
•[
writepolicy=<wb| wt| wc| nwc | fwb>]
Parameter (Optional)
•
[cachepolicy=<d | c>]
Parameter (Optional)
•
[diskcachepolicy=<enabled|disabled>]
Parameter (Optional)
Example Syntax
To change the read policy of virtual disk 4 on controller 1 to no-read-ahead,
type:
omconfig storage vdisk action=changepolicy
controller=1 vdisk=4 readpolicy=nra
omconfig Replace Member Virtual Disk
Use the following omconfig command syntax to replace the member of a
given virtual disk with the destination disk.
Complete Syntax
omconfig storage vdisk action=replacememberdisk
controller=id vdisk=id source=<PDISKID>
destination=<PDISKID>
where id is the controller ID and virtual disk ID. The <PDISK> variable
specifies the physical disk.
To obtain the values for the controller, virtual disk, and physical disk, type
omreport storage controller to display the controller IDs and then type
omreport storage vdisk controller=ID and omreport storage pdisk
controller=ID to display the IDs for the virtual disks and physical disks
attached to the controller.
Example Syntax
In this example, you are replacing physical disk 3 on connector 0 of controller 1
of virtual disk 4 with physical disk 5. On a Serial Attached SCSI (SAS)
controller, the physical disk resides in enclosure 2.
- Command Line 1
- Interface Guide 1
- Notes and Cautions 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- 9 Working With CLI 13
- Command Results 13
- 14 Contents 14
- Introduction 15
- Command Prompts 18
- Primary CLI Commands 18
- Success Messages 19
- Failure Messages 20
- Introduction 21 21
- Command Syntax Overview 23
- 24 Introduction 24
- Using the omhelp Command 25
- 28 Using the omhelp Command 28
- <command level 2> -? 37
- Commands 39
- Parameters Description 42
- Critical 46
- Server Administrator 56
- Commands for Viewing Logs 66
- <component name> 70
- Output Attributes Description 72
- Example Command Output 74
- Remote Access Information 78
- Processor 79
- Memory Array 79
- Firmware 80
- NOTE: You cannot change 87
- NOTE: The 99
- (continued) 100
- Default Warning Thresholds 116
- NOTE: extipmiusergroup 127
- Command Result Description 135
- Defining Alert Actions 137
- Available Alert Actions 138
- Example Current Probe Actions 141
- Example Fan Probe Actions 141
- Commands for Clearing Logs 142
- Action Description 143
- Severity 148
- Example Recovery Commands 150
- Example Shutdown Commands 151
- Description 152
- Ownership Values 155
- Adding Lease Information 161
- Adding Outsource Information 164
- Adding Owner Information 165
- Adding Support Information 168
- Adding System Information 170
- Adding Warranty Information 171
- Using the Storage Management 173
- Command Elements 174
- Syntax Description 175
- 178 omreport storage Commands 178
- NOTE: If a physical disk 178
- Replacing 178
- NOTE: The cachecade 179
- 180 omreport storage Commands 180
- NOTE: This command is not 181
- 182 omreport storage Commands 182
- Required Command Levels 183
- 184 omreport storage Commands 184
- NOTE: For SCSI controllers 184
- Required Command Levels (1 185
- 2, 3) and name=value pair 185
- 186 omreport storage Commands 186
- Report Commands 187
- Required Command 188
- Levels (1, 2, 3) 188
- Optional name= 188
- 190 omreport storage Commands 190
- 192 omconfig storage Commands 192
- Example for SAS Controllers 193
- Complete Syntax 201
- Example Syntax 201
- Required 203
- Command 203
- Optional name=value pairs 203
- Example Syntax to reconfigure 212
- 218 omconfig storage Commands 218
- For SAS Controllers 223
- Parameter Specification 226
- RAID 10) 228
- 244 omconfig storage Commands 244
- ° Celsius 249
- ° Celsius, type: 249
- Working With CLI Command 261 261
- Working With CLI Command 262
- Working With CLI Command 263 263
- List (lst) 265
- Table (tbl) 266
- Custom Delimited Format (cdv) 267
- 268 Working With CLI Command 268
- Index 269 269
- Index 271 271
- Index 273 273
- Index 275 275
- Index 277 277
- Index 279 279
- Index 281 281
- Index 282 282
Relacionado con productos y manuales para Servidores Dell OpenManage Server Administrator Version 6.5
Servidores Dell Lifecycle Controller 1.5 Notas
(8 paginas)
(8 paginas)
Servidores Dell PowerEdge 2970 El manual del propietario
(188 paginas)
(188 paginas)
Servidores Dell PowerEdge M605 El manual del propietario
(236 paginas)
(236 paginas)
Servidores Dell PowerEdge 6950 El manual del propietario
(166 paginas)
(166 paginas)
Servidores Dell PowerEdge C6100 Guía de usuario
(59 paginas)
(59 paginas)
Servidores Dell PowerEdge R905 Guía de inicio rápido
(58 paginas)
(58 paginas)
Servidores Dell A02 Notas
(15 paginas)
(15 paginas)
Servidores Dell PowerEdge T310 El manual del propietario
(194 paginas)
(194 paginas)
Servidores Dell V1.2 Papel blanco
(20 paginas)
(20 paginas)
Servidores Dell PowerEdge R410 Guía de inicio rápido
(50 paginas)
(50 paginas)
Servidores Dell PowerEdge R715 Guía de inicio rápido
(54 paginas)
(54 paginas)
Servidores Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) Guía de inicio rápido
(48 paginas)
(48 paginas)
Servidores Dell R300 Manual de usuario
(184 paginas)
(184 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales