Dell OpenManage Server Administrator Version 7.3 Manual de usuario Pagina 66
- Pagina / 190
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
name=value pair 1 attribute= name=value pair 2 setting= Description
attribute=crab setting=enabled | disabled
• enabled: Enables BIOS
console redirection after
system reboot.
• disabled: Disables BIOS
console redirection.
NOTE: The attribute crab is valid
for Dell PowerEdge 9G systems
only.
attribute=cpucle setting=enabled | disabled
• enabled: Enables processor
C1-E after system reboot.
• disabled: Disables processor
C1-E after system reboot.
attribute=cpuht setting=enabled | disabled
• enabled: Enables logical
processor hyperthreading.
• disabled: Disables logical
processor hyperthreading.
attribute=cpuvt setting=enabled | disabled
• enabled: Enables
virtualization.
• disabled: Disables
virtualization.
attribute=cpuxdsupport setting=enabled | disabled
• enabled: Enables Execute
Disable (XD) support on the
system.
• disabled: Disables XD support
on system.
attribute=cpucore setting=1 | 2 | 4 | 6 | 8 | 10 | 12 |all
• 1: Enables one core per
processor.
• 2: Enables two cores per
processor.
• 4: Enables four cores per
processor.
• 6: Enables six cores per
processor.
• 8: Enables eight cores per
processor.
• 10: Enables ten cores per
processor.
• 12: Enables twelve cores per
processor.
• all: Enables the maximum
cores per processor.
attribute=dbs setting=enable | disable
• enable: Enables Demand
Based Switching (DBS) on the
system.
66
- Notes, Cautions, and Warnings 2
- Contents 3
- Introduction 11
- Primary CLI Commands 12
- Success Messages 13
- Failure Messages 13
- Command Syntax Overview 14
- Using The omhelp Command 17
- Table 2. Optional Parameters 18
- Instrumentation Service 19
- Omreport Chassis Intrusion 32
- Dell License Manager Guide 39
- Omreport Licenses 44
- Commands 44
- Commands For Viewing Logs 45
- Pedestinations 49
- Remote Access 54
- Information 54
- Processor 54
- Memory Array 55
- Firmware 55
- Omreport Preferences Commands 56
- Omreport Preferences Messages 57
- Omconfig About 63
- Dell License 85
- Default Warning Thresholds 87
- License Manager 88
- Dell License Manager 89
- IPv6 address 90
- Usage Of Dracusergroup=custom 94
- Omconfig Preferences 97
- Omconfig Preferences Snmp 98
- Defining Alert Actions 100
- Available Alert Actions 101
- Commands For Clearing Logs 103
- Severity 108
- Example Recovery Commands 109
- Example Shutdown Commands 110
- Adding Lease Information 116
- Adding Outsource Information 118
- Adding Owner Information 119
- Adding Support Information 121
- Adding System Information 122
- Adding Warranty Information 122
- CLI Command Syntax 125
- Syntax Of Command Elements 126
- Omreport Storage Commands 129
- Omreport Physical Disk Status 130
- Omreport Controller Status 131
- Omreport Enclosure Status 131
- Omreport Fan Status 132
- Omreport Power Supply Status 133
- Omreport EMM Status 133
- Omreport Battery Status 134
- Omreport Global Information 135
- Omreport Connector Status 135
- Omreport Cachecade Status 136
- Omreport PCIe SSD Status 136
- Omreport Fluid Cache Status 136
- Omreport Storage Tape 137
- Omconfig Storage Commands 139
- Omconfig Blink Physical Disk 140
- Omconfig Online Physical Disk 143
- Dell OpenManage Online Help 144
- Omconfig Clear Physical Disk 145
- Omconfig Check Consistency 149
- Omconfig Blink Virtual Disk 150
- Omconfig Unblink Virtual Disk 151
- Omconfig Delete Virtual Disk 153
- Omconfig Format Virtual Disk 154
- Omconfig Secure Virtual Disk 154
- Omconfig Rename Virtual Disk 156
- Omconfig Controller Commands 157
- Omconfig Rescan Controller 159
- Dell OpenManage 160
- Online Help 160
- Controller=id 164
- Cachepolicy=<d 165
- Omconfig Set Reconstruct Rate 169
- Omconfig Set Patrol Read Mode 171
- Omconfig Start Patrol Read 171
- Omconfig Stop Patrol Read 171
- Omconfig Create Cachecade 172
- Omconfig Rekey LKM Controller 172
- Omconfig Enclosure Commands 173
- Omconfig Battery Commands 176
- Omconfig Global Commands 177
- Omconfig Connector Commands 179
- Omconfig Cachecade Commands 180
- Omconfig PCIe SSD Commands 181
- Omconfig Fluid Cache Commands 183
- Omconfig Partition Command 183
- List (lst) 188
- Table (tbl) 189
- Custom Delimited Format (cdv) 189
Relacionado con productos y manuales para Servidores Dell OpenManage Server Administrator Version 7.3
Servidores Dell Force10 S55T Manual de inicio rápido
(28 paginas)
(28 paginas)
Servidores Dell PowerEdge R720 El manual del propietario
(163 paginas)
(163 paginas)
Servidores Dell Vizioncore Guía de usuario
(13 paginas)
(13 paginas)
Servidores Dell PowerEdge R415 Guía de inicio rápido
(52 paginas)
(52 paginas)
Servidores Dell 58260075 Ficha de datos
(1 paginas)
(1 paginas)
Servidores Dell 58259908 Ficha de datos
(1 paginas)
(1 paginas)
Servidores Dell POWEREDGE R515 Manual de instalación
(58 paginas)
(58 paginas)
Servidores Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) Guía de usuario
(38 paginas)
(38 paginas)
Servidores Dell PowerEdge systems 6300 Manual de usuario
(143 paginas)
(143 paginas)
Servidores Dell PowerVault DL2100 Manual de usuario
(200 paginas)
(200 paginas)
Servidores Dell OpenManage Server Administrator Managed Node for Fluid Cache for DAS Notas
(18 paginas)
(18 paginas)
Servidores Dell PowerEdge M915 Guía de inicio rápido
(92 paginas)
(92 paginas)
Servidores Dell PowerEdge 2850 Manual de usuario
(29 paginas)
(29 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales