Dell PowerEdge 2850 Guía para resolver problemas Pagina 64
- Pagina / 76
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1. Unpack the RAID controller card and prepare it for installation.
For instructions, see the documentation accompanying the card.
2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
3. Open the system. See "Opening the System" in "Troubleshooting Your System."
4. Install the RAID controller card. See "Installing an Expansion Card" in "Installing System Options."
5. Connect SCSI interface cables supplied with the card to the SCSIA and/or SCSIB connectors on the SCSI backplane board.
To identify the connector on the RAID controller card, see documentation for the card. See FigureA-6 to locate the SCSI controller connectors on the
SCSI backplane board.
Route the SCSI cables over the SCSI backplane board to the expansion-card cage.
6. Connect the external SCSI devices to the card's external connector on the system's back panel.
If you are attaching multiple external SCSI devices, daisy-chain the devices to each other using the cables shipped with each device.
7. Close the system. See "Closing the System" in "Troubleshooting Your System."
8. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.
9. Install any required SCSI device drivers. See "Installing and Configuring SCSI Drivers" in the User's Guide.
10. Test the SCSI devices.
Test a SCSI hard drive by running the SCSI Controllers test in the system diagnostics.
Installing a SCSI Backplane Daughter Card
To operate the SCSI backplane in a 2/4 split backplane configuration, you must install a daughter card.
1. Unpack the SCSI backplane board daughter card kit.
2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
3. Open the system. See "Opening the System" in "Troubleshooting Your System."
4. Disconnect the control panel cable from its backplane connector. See Figure7-6.
The SCSI backplane daughter card connector and card guide are located in the compartment below the control panel cable.
5. The daughter card fits between the sides of the card guide. To install the daughter card in the card guide and to connect it to the backplane connector,
performing the following steps:
a. Ensure that the retention lever is in the open position.
b. Hold the daughter card by its edges with the card connector facing the SCSI backplane board and the card's retention peg facing the retention
lever. See Figure7-6.
c. Lower the card into the card guide.
d. Close the retention lever to slide the daughter card into the SCSI backplane connector and lock the card into place. See Figure7-6.
6. Reconnect the control panel cable to its backplane connector. See Figure7-6.
Figure 7-6. Installing a SCSI Backplane Daughter Card
NOTE: Cables can be connected from the RAID controller card to SCSIA and/or SCSIB backplane board connector(s). A backplane board connector
that is not attached to the RAID controller card uses the integrated SCSI controller or optional integrated RAID controller if it is attached to the
riser board.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See
your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against
electrostatic discharge.
- Notes, Notices, and Cautions 1
- Abbreviations and Acronyms 1
- Jumpers and Connectors 2
- System Board Connectors 3
- I/O Connectors 7
- Video Connector 8
- USB Connectors 9
- Integrated NIC Connectors 9
- Network Cable Requirements 10
- Introduction 11
- Power Indicator Codes 15
- NIC Indicator Codes 15
- LCD Status Messages 16
- System Messages 18
- Table 2-9.SystemMessages 19
- System Beep Codes 21
- Warning Messages 23
- Diagnostics Messages 23
- Alert Messages 23
- Before You Begin 24
- From the Utility Partition 26
- Error Messages 27
- Start-Up Routine 28
- Checking the Equipment 28
- Troubleshooting the Keyboard 29
- Troubleshooting the Mouse 29
- Troubleshooting a NIC 31
- Inside the System 31
- Removing the Bezel 32
- Replacing the Bezel 32
- Opening the System 33
- Closing the System 33
- Problem 34
- Troubleshooting a Fan 36
- Installing System Options 45
- Power Supplies 46
- Expansion-Card Cage 46
- Expansion Cards 48
- Removing an Expansion Card 49
- System Memory 50
- Installing Memory Modules 51
- Processors 52
- System Battery 54
- Installing Drives 58
- SCSI Hard Drives 59
- Installing a SCSI Hard Drive 60
- Removing a SCSI Hard Drive 60
- Getting Help 66
- Problems With Your Order 67
- Product Information 67
- Before You Call 68
- Dell Contact Numbers 68
Relacionado con productos y manuales para Servidores Dell PowerEdge 2850
Servidores Dell 4.x Guía de usuario
(44 paginas)
(44 paginas)
Servidores Dell PowerEdge R820 Cómo utilizar
(21 paginas)
(21 paginas)
Servidores Dell PowerEdge 2650 Manual de usuario
(43 paginas)
(43 paginas)
Servidores Dell Microsoft Windows Compute Cluster Server 2003 Service Pack 1 Manual de instalación
(20 paginas)
(20 paginas)
Servidores Dell PowerEdge R910 El manual del propietario
(210 paginas)
(210 paginas)
Servidores Dell PowerEdge R815 Guía de inicio rápido
(50 paginas)
(50 paginas)
Servidores Dell PowerEdge T710 Guía de inicio rápido
(50 paginas)
(50 paginas)
Servidores Dell R2 Manual de usuario
(103 paginas)
(103 paginas)
Servidores Dell PowerEdge R810 Guía de inicio rápido
(60 paginas)
(60 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.315 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales