Dell PowerVault DP500 Manual de usuario Pagina 56
- Pagina / 86
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing the Control Panel Assembly
1. Insert the display module into the chassis cutout and secure with the two Torx screws.
2. Affix the display module label to the display module.
3. Install the control panel board in the system chassis and secure with the three Phillips screws. See Figure3-34.
4. Connect the display module cable to the control panel board. See Figure3-34.
5. Connect the control panel cable to the control panel board. See Figure3-34.
6. Close the system. See Closing the System.
7. Reconnect the system to the power source and turn on the system and attached peripherals.
8. If applicable, install the bezel.
System Board (Service-only Procedure)
Removing the System Board
1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
2. Open the system. SeeOpening the System
3. If applicable, remove any expansion cards. See Installing an Expansion Card
4. Remove the expansion-card cage. See Removing the Expansion-Card Cage
5. Remove the cooling shroud. See Removing the Cooling Shroud.
6. Remove the fans. See Removing a System Fan.
7. Remove the fan bracket. See Removing the Fan Bracket
8. If applicable, remove the RAC card. See Installing a RAC Card
9. Remove the memory modules. See Removing Memory Modules.
10. Remove the heatsink(s) and microprocessor(s). See Removing a Processor.
11. Remove the TOE key, if present. See Figure6-2 for the location of the TOE key.
12. Remove the sideplane. See Removing the Sideplane Board.
1
display module label
2
display module securing screws (2)
3
display module
4
display module cable
5
control panel cable
6
control panel circuit board
7
control-panel circuit board securing screws (3)
CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See
your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against
electrostatic discharge.
CAUTION: The DIMMs are hot to the touch for some time after the system has been powered down. Allow time for the DIMMs to cool before
handling them. Handle the DIMMs by the card edges and avoid touching the DIMM components.
NOTE: While removing the memory modules, record the memory module socket locations to ensure proper installation.
- About Your System 2
- Hard-Drive Indicator Codes 3
- Power Indicator Codes 5
- NIC Indicator Codes 5
- LCD Status Messages 6
- Removing LCD Status Messages 8
- System Messages 9
- Warning Messages 11
- Diagnostics Messages 11
- Alert Messages 11
- Getting Help 15
- Glossary 16
- Recommended Tools 22
- Inside the System 23
- Front Bezel 23
- Removing the Front Bezel 24
- Replacing the Front Bezel 24
- Opening the System 24
- Closing the System 24
- Hard Drives 25
- Installing a Drive Blank 26
- Power Supplies 29
- System Fans 30
- Cooling Shroud 31
- Fan Brackets 32
- Replacing the Fan Bracket 33
- RAID Battery 35
- Expansion Cards 36
- Expansion-Card Cage 37
- Installing a RAC Card 38
- Optical Drive 39
- Diskette Drive 40
- SCSI Tape Drive 42
- System Memory 44
- Memory Sparing Support 45
- Memory Mirroring Support 45
- Installing Memory Modules 45
- Removing Memory Modules 46
- Processors 47
- Installing a Processor 48
- System Battery 49
- Sideplane Board 52
- SAS Backplane Board 53
- Removing the System Board 56
- Installing the System Board 57
- Jumpers and Connectors 59
- Sideplane Board Connectors 61
- System Setup Options 64
- Memory Information Screen 65
- CPU Information Screen 66
- Integrated Devices Screen 66
- Serial Communication Screen 67
- System Security Screen 67
- Exit Screen 68
- Using the System Password 69
- Using the Setup Password 70
- BMC Setup Module Options 71
- Start-Up Routine 72
- Checking the Equipment 72
- Troubleshooting the Keyboard 73
- Troubleshooting the Mouse 74
- Problem 75
- Troubleshooting a NIC 76
- Troubleshooting a Fan 78
Relacionado con productos y manuales para Hardware De La Computadora Dell PowerVault DP500
Hardware De La Computadora Dell PowerVault 735N (Rackmount NAS Appliance) Manual de usuario
(12 paginas)
(12 paginas)
Hardware De La Computadora Dell PowerVault 122T SDLT 320 (Autoloader) Manual de usuario
(39 paginas)
(39 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales