Dell PowerVault DP500 Manual de usuario Pagina 78
- Pagina / 86
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting Power Supplies
Problem
l System-status indicators are amber.
l Power-supply fault indicators are amber.
l Front-panel status LCD indicates a problem with the power supplies.
Action
1. Run the appropriate online diagnostics test. See Using Server Administrator Diagnostics.
2. Locate the faulty power supply.
The power supply's fault indicator is lit. See Power Indicator Codes.
Remove the faulty power supply. See Removing a Power Supply.
3. Ensure that the power supply is properly installed by removing and reinstalling it. See Replacing a Power Supply.
4. Check the indicators to see if the problem is resolved. If not, remove the faulty power supply. See Removing a Power Supply.
5. Install a new power supply. See Replacing a Power Supply.
If the problem persists, see Getting Help.
Troubleshooting System Cooling Problems
Problem
l Systems management software issues a fan-related error message.
Action
Ensure that none of the following conditions exist:
l Ambient temperature is too high.
l External airflow is obstructed.
l Cables inside the system obstruct airflow.
l An individual cooling fan has failed. See Troubleshooting a Fan.
Troubleshooting a Fan
NOTE: Some software may cause the system time to speed up or slow down. If the system seems to operate normally except for the time kept in the
System Setup program, the problem may be caused by software rather than by a defective battery.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system.
Before performing any procedure, see your Product Information Guide for complete information about safety precautions, working inside the
computer and protecting against electrostatic discharge.
NOTICE: You can hot-plug the power supplies. One power supply must be installed for the system to operate. The system is in the redundant mode
when two power supplies are installed. Remove and install only one power supply at a time in a system that is powered on. Operating the system for
extended periods of time with only one power supply installed, without a power supply blank installed, can cause the system to overheat.
NOTE: After installing a power supply, allow several seconds for the system to recognize the power supply and to determine if it is working
properly. The power indicator turns green to signify that the power supply is functioning properly. See Power Indicator Codes.
- About Your System 2
- Hard-Drive Indicator Codes 3
- Power Indicator Codes 5
- NIC Indicator Codes 5
- LCD Status Messages 6
- Removing LCD Status Messages 8
- System Messages 9
- Warning Messages 11
- Diagnostics Messages 11
- Alert Messages 11
- Getting Help 15
- Glossary 16
- Recommended Tools 22
- Inside the System 23
- Front Bezel 23
- Removing the Front Bezel 24
- Replacing the Front Bezel 24
- Opening the System 24
- Closing the System 24
- Hard Drives 25
- Installing a Drive Blank 26
- Power Supplies 29
- System Fans 30
- Cooling Shroud 31
- Fan Brackets 32
- Replacing the Fan Bracket 33
- RAID Battery 35
- Expansion Cards 36
- Expansion-Card Cage 37
- Installing a RAC Card 38
- Optical Drive 39
- Diskette Drive 40
- SCSI Tape Drive 42
- System Memory 44
- Memory Sparing Support 45
- Memory Mirroring Support 45
- Installing Memory Modules 45
- Removing Memory Modules 46
- Processors 47
- Installing a Processor 48
- System Battery 49
- Sideplane Board 52
- SAS Backplane Board 53
- Removing the System Board 56
- Installing the System Board 57
- Jumpers and Connectors 59
- Sideplane Board Connectors 61
- System Setup Options 64
- Memory Information Screen 65
- CPU Information Screen 66
- Integrated Devices Screen 66
- Serial Communication Screen 67
- System Security Screen 67
- Exit Screen 68
- Using the System Password 69
- Using the Setup Password 70
- BMC Setup Module Options 71
- Start-Up Routine 72
- Checking the Equipment 72
- Troubleshooting the Keyboard 73
- Troubleshooting the Mouse 74
- Problem 75
- Troubleshooting a NIC 76
- Troubleshooting a Fan 78
Relacionado con productos y manuales para Hardware De La Computadora Dell PowerVault DP500
Hardware De La Computadora Dell PowerVault 735N (Rackmount NAS Appliance) Manual de usuario
(12 paginas)
(12 paginas)
Hardware De La Computadora Dell PowerVault 122T SDLT 320 (Autoloader) Manual de usuario
(39 paginas)
(39 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.841 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales