Dell Active Fabric Manager Guía de usuario Pagina 68
- Pagina / 179
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
• low latency — The access layer uses S55 switches
Resiliency In MXL (Routed VLT)
• Intra-chassis — Within the chassis (mVLT)
• Inter-chassis resiliency — Across 2 chassis (VLT)
This section contains the following topics:
• (Optional) Configuring Advanced Options
• Selecting the Fabric Deployment Type
(Optional) Configuring Advanced Options
For a Layer 2 or Layer 3 with Resiliency (Routed VLT) fabric, you customize the bandwidth between the aggregation and
access switches. When you configure the fabric link bandwidth between aggregation and access switches from the
Enabled Link Bandwidth Customization option from the Deployment Topology screen, the bandwidth selected is shared
equally by 2 redundant links. For example, if you select a fabric link bandwidth of 80 Gb between the aggregation and
access switches, you can configure 40 GB for each redundant link on the Fabric Customization screen.
To configure the deployment type so that you can customize the fabric link bandwidth between the aggregation and
access switches:
1. In the Deployment Topology, check one of the following options:
– Layer 2
– Layer 3 with Resiliency (Routed VLT)
2. Check the Enabled Link Bandwidth Customization option.
Figure 31. Enabled Link Bandwidth Customization Option
3. In the Fabric Link Core Aggregation and aggregation and Access option (only the applicable options for a select
topology are configurable), select the fabric bandwidth value from the Aggregation and Access pull-down menu.
For example, for 2 tier topology, selecting the 120 Gb bandwidth option allows you to later customize the
bandwidth from 20 to 120 Gb in increments of 20 Gb in the Fabric Customization screen.
4. Click the Refresh Deployment Type button.
68
- Active Fabric Manager (AFM) 1
- Deployment Guide 2.0 1
- Contents 3
- Introduction 9
- About AFM 11
- Getting Started 13
- Figure 2. Capacity Planning 15
- Figure 3. Provisioning 16
- AFM Site Map 17
- Supported Fabric Types 19
- VLT) Fabric 20
- Conventional Core 21
- Distributed Core 22
- Key Advantages 22
- Distributed Core Terminology 23
- FTOS Configuration Guide 24
- Multi-domain VLT 31
- VLT Terminology 31
- VLT Fabric Terminology 31
- VLT Components 32
- Typical VLT Topology 32
- 10 Gb or 40 Gb ToR (mVLT) 37
- Designing the Fabric 49
- Table 12. Switch Level States 51
- AFM Plug-in for 53
- Openstack 53
- Deployment Topology Use Cases 55
- Use Case 3: 2 Tier Layer 2 57
- Use Case 5: 3 Tier Layer 2 62
- Deleting the Fabric 77
- Viewing the Wiring Diagram 77
- Fabric Deployment Summary 79
- Pre-Deployment Configuration 83
- Pre-Deployment Flowchart 84
- Pre-Deployment Screens 84
- Fabric Name 101
- Fabric Name 105
- AFM Installation Guide 107
- Open Automation Guide 108
- Open Automation Guide 108
- Deploying the Fabric 109
- Advanced Configuration 112
- Associating Templates 113
- Validation 115
- Validating the Fabric 116
- Custom CLI Configuration 117
- Editing Templates 118
- Deleting Templates 118
- Editing Template Associations 120
- Viewing the Fabric 123
- Switch Name 124
- Network Topology 125
- Fabric Summary 127
- Switch Summary 129
- Troubleshooting 131
- Validation Alarms 132
- Pre-deployment Errors 134
- Deployment Errors 134
- Validation Errors 135
- Table 34. Wiring Errors 136
- TFTP/FTP Error 143
- Alerts and Events 145
- Performance Management 149
- Fabric Performance Management 150
- Switch Performance Management 150
- Port Performance Management 151
- Data Collection 152
- Threshold Settings 153
- Creating New Reports 154
- Editing Reports 155
- Running Reports 155
- Duplicating Reports 155
- Deleting Reports 156
- Maintenance 157
- Updating the Switch Software 158
- Replacing a Switch 158
- Step 2: Replacing a Switch 159
- Updating the AFM 160
- Displaying Job Results 163
- Scheduling Jobs 163
- Switch Backup 164
- Switch Software Updates 164
- Switch Software Activation 165
- Administration 169
- Fabric 170
- CLI Credentials 171
- Client Settings 171
- Data Retention Settings 172
- DHCP Server Settings 172
- NTP Server Settings 172
- SMTP Email 173
- SNMP Configuration 173
- Syslog Server IP Addresses 173
- System Information 173
- Managing User Accounts 174
- Adding a User 175
- Deleting a User 176
- Editing a User 176
- Unlocking a User 177
- Changing Your Password 177
- Managing User Sessions 178
- Audit Log 178
Relacionado con productos y manuales para Redes Dell Active Fabric Manager
Redes Dell Studio Desktop Guia de preparacion
(62 paginas)
(62 paginas)
Redes Dell B-DCX-4s Manual de usuario
(16 paginas)
(16 paginas)
Redes Dell Managed PDU LED Manual de usuario
(244 paginas)
(244 paginas)
Redes Dell PowerEdge 2970 Manual de instalación
(25 paginas)
(25 paginas)
Redes Dell PowerEdge M1000e Guía de usuario
(7 paginas)
(7 paginas)
Redes Dell PowerConnect W-IAP108/109 Guía de usuario
(497 paginas)
(497 paginas)
Redes Dell R2 Guía de inicio rápido
(122 paginas)
(122 paginas)
Redes Dell R1 Manual de usuario
(16 paginas)
(16 paginas)
Redes Dell PowerConnect W-IAP3WN/P Manual de usuario
(377 paginas)
(377 paginas)
Redes Dell Networking S6000 Guía de inicio rápido
(37 paginas)
(37 paginas)
Redes Dell PowerEdge T110 II Manual de usuario
(24 paginas)
(24 paginas)
Redes Dell 3-DNS Guia de preparacion
(16 paginas)
(16 paginas)
Redes Dell Wyse ThinOS V10LE Manual de usuario
(14 paginas)
(14 paginas)
Redes Dell PowerEdge T620 Especificaciones
(39 paginas)
(39 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales