Dell 3348 - PowerConnect Switch - Stackable Guía de usuario Pagina 1

www.dell.com | support.dell.comDell™ PowerConnect™ 3324/3348User’s GuideModel PowerConnect 3324/3348

10 ContentsDefining QoS Global Parameters . . . . . . . . . . . . . . . . . 339Configuring Global QoS Settings. . . . . . . . . . . . . . . . 340De

100 Getting Startedwww.dell.com | support.dell.com• Line Interface—Contains commands to configure the management connections. These include commands s

Getting Started 101Telnet ConnectionTelnet is a terminal emulation TCP/IP protocol. ASCII terminals can be virtually connected to the local device thr

102 Getting Startedwww.dell.com | support.dell.com

SECTION 6Configuring System InformationDefining General Device InformationManaging LogsDefining Device IP AddressesManaging Device SecurityDefining SN

104 Configuring System Informationwww.dell.com | support.dell.comThis section provides information about defining system parameters including security

Configuring System Information 105General PageViewing the Asset PageThe Asset page contains parameters for configuring general device information, inc

106 Configuring System Informationwww.dell.com | support.dell.comAsset PageThe Asset page contains the following fields: • System Name—Defines the use

Configuring System Information 107• Asset Tag—Specifies the user-defined device reference.• Serial No.—Indicates the serial number of the device.Defin

108 Configuring System Informationwww.dell.com | support.dell.comConsole (config)# snmp-server location New_YorkConsole (config)# exitConsole # exitCo

Configuring System Information 109Viewing System Health InformationThe System Health page physical device hardware information. To open the System Hea

SECTION 1OverviewSystem DescriptionPowerConnect 3324/3348 Stacking OverviewPowerConnect User Guide OverviewPowerConnect 3324/3348 CLI Documentation

110 Configuring System Informationwww.dell.com | support.dell.com– —Indicates the redundant power supply is not operating normally for the specified u

Configuring System Information 111Versions PageThe Versions page contains the following information:• Unit No.—Indicates the stacking unit number.• So

112 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console> show versionSW version

Configuring System Information 113Resetting the device:1 Open the Reset page.2 Click Reset. A confirmation message displays:Device Reset Confirmation

114 Configuring System Informationwww.dell.com | support.dell.comLogs PageThe Logs page contains links to the following pages: • Defining Global Log P

Configuring System Information 115Event messages have a unique format, as per the SYSLOG RFC recommended message format for all error reporting; for e

116 Configuring System Informationwww.dell.com | support.dell.comGlobal Log Parameters Page The Global Log Parameters page contains the following fiel

Configuring System Information 117– Warning—Indicates the lowest level of a device warning. The device is functioning, but an operational problem has

118 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# logging onConsole

Configuring System Information 119The RAM Log Table page contains the following fields:• Log Index—Indicates the log number in the RAM Log Table.• Log

12 Overviewwww.dell.com | support.dell.comSystem DescriptionThe Dell™ PowerConnect™ 3324 and 3348 devices are standalone and stackable advanced Layer

120 Configuring System Informationwww.dell.com | support.dell.comBuffer log:11-Aug-2002 15:41:43: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed s

Configuring System Information 121Displaying the Log File TableThe Log File Table contains information about log entries saved to the Log File in FLAS

122 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console # show logging fileConsole l

Configuring System Information 12311-Aug-2002 15:41:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/e0, changed state to down11-Aug-2002

124 Configuring System Informationwww.dell.com | support.dell.com• UDP Port (1-65535)—Indicates the UDP port to which the logs are sent for the select

Configuring System Information 125Add a Log Server PageIn addition to the fields in the Remote Logs Server Settings page, the Add a Log Server page co

126 Configuring System Informationwww.dell.com | support.dell.comRemoving a Log Server from the Log Servers Table page:1 Open the Remote Logs Server S

Configuring System Information 127The IP Addressing page contains links to the following pages:• Defining Default Gateways• Defining IP Interfaces• De

128 Configuring System Informationwww.dell.com | support.dell.comThe Default Gateway page contains the following fields: • Default Gateway—Indicates t

Configuring System Information 1293 Define the Default Gateway IP Address field.ORSet the new gateway as active by checking the check box.4 Click Appl

Overview 13During the stacking setup, one device is selected by the network administrator as the stack master, while all other devices are selected as

130 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# ip default-gateway

Configuring System Information 131– Port—Indicates that the IP address was assigned to a port.– LAG—Indicates that the IP address was assigned to a Li

132 Configuring System Informationwww.dell.com | support.dell.comIP Interface Table PageDeleting IP addresses:1 Open the IP Interface page.2 Click Sho

Configuring System Information 133Internet address is 10.7.1.192/24console# show ip interface vlan 204 IP Address Directed Broadcast-----

134 Configuring System Informationwww.dell.com | support.dell.comThe DCHP IP Interface page contains the following fields:• Interface—Select an interf

Configuring System Information 135Modifying a DCHP IP Interface:1 Open the DHCP IP Interface page.2 Modify the Interface field.3 Click Apply Changes.

136 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# interface ethernet

Configuring System Information 137The ARP Settings page contains the following fields: • ARP Entry Age Out (0-4000000)—Indicates the amount of time (s

138 Configuring System Informationwww.dell.com | support.dell.comAdd ARP Entry Page3 Select an Interface and define its IP Address and MAC address fie

Configuring System Information 139The following is an example of the CLI commands: console(config)# arp 146.1.0.131 00-00-55-66-77-00 ethernet 1/e1Con

14 Overviewwww.dell.com | support.dell.comWhen the master unit boots or when inserting or removing a stack member, the master unit initiates a stackin

140 Configuring System Informationwww.dell.com | support.dell.comManagement Security PageThis section includes the following topics:• Defining Access

Configuring System Information 141Defining Access ProfilesThe Access Profiles page allows network managers to define profiles and rules for accessing

142 Configuring System Informationwww.dell.com | support.dell.comThe Access Profiles page contains the following fields: • Access Profile State—Enable

Configuring System Information 143Add An Access Profile PageThe Add An Access Profile page contains the following fields:• Access Profiles Name—Specif

144 Configuring System Informationwww.dell.com | support.dell.com• Source IP Address—Indicates the interface Source IP Address to which the packet is

Configuring System Information 145• Management Method—Specifies the management method for which the access profile is defined. The possible field valu

146 Configuring System Informationwww.dell.com | support.dell.com5 Click Apply Changes. The rule is added, and the device is updated.Viewing the Profi

Configuring System Information 147The following is an example of the CLI commands: Console (config)# management access-list mlistConsole (config-macl)

148 Configuring System Informationwww.dell.com | support.dell.comConsole (config)# management access-class mlistConsole (config)# exitConsole# show ma

Configuring System Information 149Authentication Profiles PageThe Authentication Profiles page contains the following options lists:• Authentication P

Overview 15Rearranging StacksThe stacking order can be changed by either removing a stack member or by rearranging the stacking cables. The order in w

150 Configuring System Informationwww.dell.com | support.dell.com• Remove—Removes the selected Authentication Profile from the Authentication Profile

Configuring System Information 151Authentication Profile PageDeleting an Authentication Profile: 1 Open the Authentication Profiles page.2 Click Show

152 Configuring System Informationwww.dell.com | support.dell.comAssigning Authentication ProfilesAfter Authentication Profiles are defined, the Authe

Configuring System Information 153• Telnet—Displays the Authentication Profiles used to authenticate Telnet users. Authentication Profiles are assigne

154 Configuring System Informationwww.dell.com | support.dell.com• Secure HTTP—Specifies the authentication profiles used for Secure HTTP access. The

Configuring System Information 1553 Click Apply Changes. Telnet sessions are assigned an Authentication List.Applying an Authentication Profile to Sec

156 Configuring System Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config-line)# enable authen

Configuring System Information 157Defining the Local User DatabasesThe Local User Database page allows network managers to define users, passwords and

158 Configuring System Informationwww.dell.com | support.dell.com– Checked—Removes a specific user from the Local User Database.– Unchecked—Maintains

Configuring System Information 159Local User Table PageDeleting Users: 1 Open the Local User Database page.2 Click Show All. The Local User Table page

16 Overviewwww.dell.com | support.dell.comPowerConnect 3324 Replaces PowerConnect 3348• If a PowerConnect 3348 replaces PowerConnect 3348, the new 48

160 Configuring System Informationwww.dell.com | support.dell.comDefining Line Passwords The Line Passwords page allows network managers to define lin

Configuring System Information 161Defining line passwords for console sessions: 1 Open the Line Password page.2 Define the Line Password for Console f

162 Configuring System Informationwww.dell.com | support.dell.com• Click System > Management Security > Enable Passwords in the Tree View. The M

Configuring System Information 163The following is an example of the CLI commands: Console (config)# enable password level 15 dellConsole# show users

164 Configuring System Informationwww.dell.com | support.dell.comRADIUS Settings PageThe RADIUS Settings page contains the following fields:• IP Addre

Configuring System Information 165The following fields set the RADIUS default values: • Default Timeout for Reply (1-30)—Specifies the default amount

166 Configuring System Informationwww.dell.com | support.dell.com3 Define the IP Address, Priority, Authentication Port, Number of Retries, Timeout fo

Configuring System Information 167The following is an example of the CLI commands: Console (config)# radius-server timeout 5Console (config)# radius-s

168 Configuring System Informationwww.dell.com | support.dell.com172.16.1.216451646118 02Defining SNMP ParametersSimple Network Management Protocol (

Configuring System Information 169Defining CommunitiesThe system administrator manages access rights (read and write, read only, and so on.) by defini

Overview 17PowerConnect User Guide OverviewThe PowerConnect User Guide is divided into two parts: • About Installing the PowerConnect 3324/3348 Switch

170 Configuring System Informationwww.dell.com | support.dell.com– SNMP Admin—Indicates that the user has access to all device configuration options,

Configuring System Information 171Community Table PageDeleting Communities:1 Open the SNMP Community page.2 Click Show All. The Community Table page o

172 Configuring System Informationwww.dell.com | support.dell.comSNMP Trap Settings PageThe SNMP Trap Settings page contains the following fields:• SN

Configuring System Information 173– Checked—Removes the Trap Manager Table entry. – Unchecked—Maintains the Trap Manager Table entry.Enabling SNMP Tra

174 Configuring System Informationwww.dell.com | support.dell.comDisplaying the Trap Managers Table:The Trap Managers Table contains fields for config

Configuring System Information 175The following is an example of the CLI commands: Console (config)# snmp-server enable trapsConsole (config)# snmp-se

176 Configuring System Informationwww.dell.com | support.dell.comFile Management OverviewThe configuration file structure consists of the following fi

Configuring System Information 177File Management PageThe File Management page contains links to: • Downloading Files• Uploading Files• Resetting the

178 Configuring System Informationwww.dell.com | support.dell.comFile Download From Server PageThe File Download from Server page contains the followi

Configuring System Information 179• Configuration Download File Destination—Indicates the destination file to which to the configuration files is down

18 Overviewwww.dell.com | support.dell.com• Configuring Quality of Service—Contains information about configuring device Class of Service.• Getting He

180 Configuring System Informationwww.dell.com | support.dell.comCopy took 0:01:11 [hh:mm:ss]Uploading FilesThe File Upload to Server page contains fi

Configuring System Information 181• Configuration Upload Destination—Specifies the Configuration file path from which the file is uploaded.• Configura

182 Configuring System Informationwww.dell.com | support.dell.comResetting the Active ImageThe Active Images page allows network managers to select an

Configuring System Information 1833 Click Apply Changes. The Image file is selected. The Image file reloads only after the next reset. The currently s

184 Configuring System Informationwww.dell.com | support.dell.comCopy Files PageThe Copy Files page contains the following fields: • Copy Master Firmw

Configuring System Information 185• Restore Configuration Factory Defaults—Restores the Factory Configuration default files by erasing the Startup-Con

186 Configuring System Informationwww.dell.com | support.dell.comAccessing file 'file1' on 172.16.101.101.Loading file1 from 172.16.101.101:

Configuring System Information 187Configuring General Device Tuning ParametersThe General Settings page allows network managers to define general devi

188 Configuring System Informationwww.dell.com | support.dell.comViewing RAM Log Entries Counter Using the CLI CommandsThe following table summarizes

SECTION 7Configuring Switch InformationConfiguring Network SecurityConfiguring PortsConfiguring Address TablesConfiguring GARPConfiguring the Spanning

SECTION 2Hardware DescriptionPowerConnect 3324/3348 DescriptionPorts DescriptionLED Definitions

190 Configuring Switch Informationwww.dell.com | support.dell.comThis section provides all system operation and general information for configuring ne

Configuring Switch Information 191Network Security PageThe Network Security page contains links to the following topics: • Network Security Overview•

192 Configuring Switch Informationwww.dell.com | support.dell.com• Wild Card Masks• Match DSCP• Match IP-Precedence• Source MAC Address• Destination M

Configuring Switch Information 193Configuring Port SecurityNetwork users can be limited to specific ports or LAGs with Locked Ports. Locked Port is re

194 Configuring Switch Informationwww.dell.com | support.dell.com• Set Port—Indicates that the port is either locked or unlocked. The possible field v

Configuring Switch Information 195Port Security Table PageIn addition to the fields displayed in the Port Security Page, the Port Security Table page

196 Configuring Switch Informationwww.dell.com | support.dell.com5/7 Discard Enable 100 887/8 Discard DisableDefining IP

Configuring Switch Information 197• Source IP Address—Matches the source IP address to which packets are addressed to the ACE. • Wild Card Mask—Indica

198 Configuring Switch Informationwww.dell.com | support.dell.comAdd IP Based ACL Page3Define the ACL Name, New Ace Priority, Protocol, Source and Des

Configuring Switch Information 199ACEs Associated with IP-ACLModifying an IP-based ACE:1 Open the Add ACE to IP Based ACL page. 2 Click Show All.The A

Notes, Notices, and Cautions NOTE: Notes indicate important information that helps you make better use of your device. NOTICE: Notices indicate either

20 Hardware Descriptionwww.dell.com | support.dell.comPowerConnect 3324/3348 DescriptionPowerConnect 3324/3348 DimensionsThis device has the following

200 Configuring Switch Informationwww.dell.com | support.dell.comAssigning IP-based ACEs to ACLs Using the CLI CommandsThe following table summarizes

Configuring Switch Information 201Add ACE to MAC Based ACL PageThe Add ACE to MAC Based ACL page contains the following fields: • ACL Name—Contains a

202 Configuring Switch Informationwww.dell.com | support.dell.com• VLAN ID—Matches the packet’s VLAN ID to the ACE.• Action—Indicates the ACE forwardi

Configuring Switch Information 203Displaying ACL-specific ACEs:1 Open the Add ACE to MAC Based ACL page. 2 Click Show All. The ACEs Associated with MA

204 Configuring Switch Informationwww.dell.com | support.dell.com4 Check the Remove check box.5 Click Apply Changes. The MAC-based ACE is removed, and

Configuring Switch Information 205The following is an example of the CLI commands: Console (config)# mac access-list dellConsole (config-mac-al)# perm

206 Configuring Switch Informationwww.dell.com | support.dell.comACL Bindings PageThe ACL Bindings page contains the following fields:• Select an Inte

Configuring Switch Information 2073 Define the interface to which the ACL is attached in the Attach ACL to an Interface field. 4 Click Apply Changes.

208 Configuring Switch Informationwww.dell.com | support.dell.comPorts PageThis section includes the following topics: • Defining Port Parameters• Def

Configuring Switch Information 209Port ConfigurationThe Port Configuration page contains the following fields: • Port—Specifies the port number.• Desc

Hardware Description 21General Device ComponentsThe PowerConnect 3324/3348 includes the following hardware components: • CPU—Based on Motorola’s MPC 8

210 Configuring Switch Informationwww.dell.com | support.dell.com• Current Port Status—Specifies the port operational status. The possible field value

Configuring Switch Information 211– Disable—Disables auto negotiation on the port. This is the default value.– Current Auto Negotiation—Indicates the

212 Configuring Switch Informationwww.dell.com | support.dell.comThe following table describes the parameter combination settings required to configur

Configuring Switch Information 213Ports Configuration TableIn addition to the Port Configuration page fields, the Port Configuration Table also displa

214 Configuring Switch Informationwww.dell.com | support.dell.comThe following table summarizes the equivalent CLI commands for configuring ports as d

Configuring Switch Information 215The following is an example of the CLI commands: Console (config)# interface ethernet 1/e5Console (config-if)#Consol

216 Configuring Switch Informationwww.dell.com | support.dell.comPortPortDuplexSpeed NegFlowBackMDILink ContPresModeState ----------------------------

Configuring Switch Information 217To open the LAG Configuration page: NOTE: If port configuration is modified while the port is a LAG member, the con

218 Configuring Switch Informationwww.dell.com | support.dell.com• Current LAG Status—Specifies the LAG status. The possible field values are: – Up—In

Configuring Switch Information 219– Half—The interface supports transmission between the device and the client in only one direction at a time.• Flow

22 Hardware Descriptionwww.dell.com | support.dell.comMode ButtonThe Mode Button toggles between port activity and port duplex settings. Stack ID Butt

220 Configuring Switch Informationwww.dell.com | support.dell.comLAG Configuration TableConfiguring LAGs with CLI CommandsThe following is an example

Configuring Switch Information 221The following message displays:console# sh interfaces status port-channel 1Flow Link Backch Type Duplex Speed Neg Co

222 Configuring Switch Informationwww.dell.com | support.dell.comEnabling Storm ControlA Broadcast Storm is a result of an excessive amount of broadca

Configuring Switch Information 223– All Fast Ethernet Ports—Indicates that storm control is enabled for all FE ports. Storm control can be applied ind

224 Configuring Switch Informationwww.dell.com | support.dell.comDisplaying the Port Parameters Table:1 Open the Storm Control page .2 Click Show All.

Configuring Switch Information 225[Packets/sec]-------------- -------- --------- -------- -----------Gigaethernet 1 Enabled Disabled Enabled 2000Gigae

226 Configuring Switch Informationwww.dell.com | support.dell.com• Ports cannot be configured as a destination port.• All packets are tagged when they

Configuring Switch Information 227• Destination Port—Defines the port number to which port traffic is mirrored. A copy port cannot mirror itself, cann

228 Configuring Switch Informationwww.dell.com | support.dell.comDeleting a copy port from a port mirroring session: 1 Open the Port Mirroring page.2

Configuring Switch Information 229Configuring Address TablesMAC addresses are stored in either the Static Address or the Dynamic Address databases. A

Hardware Description 23Stacking ConnectionsFor more information about connecting Stacking cables, see "Connecting Stacking Cables". TxRxTxRx

230 Configuring Switch Informationwww.dell.com | support.dell.comDefining Static AddressesThe Static MAC Address page contains a list of static MAC ad

Configuring Switch Information 231– Delete on Reset—Indicates the MAC address is deleted when the device is reset.– Timeout—Indicates the MAC address

232 Configuring Switch Informationwww.dell.com | support.dell.comRemoving a static address from the Static Address Table:1 Open the Static Address Tab

Configuring Switch Information 233Viewing Dynamic AddressesThe Dynamic Address page contains information about querying the Dynamic Address Tab le, in

234 Configuring Switch Informationwww.dell.com | support.dell.com• Address Table Sort Key—Specifies the method by which the Dynamic Address Table is s

Configuring Switch Information 235The following is an example of the CLI commands: Console (config)# bridge aging-time 250Console (config)# exitConsol

236 Configuring Switch Informationwww.dell.com | support.dell.comGARP PageThis section includes the following topic:• Defining GARP TimersDefining GAR

Configuring Switch Information 237GARP Timers PageThe GARP Timers page contains the following fields:• Interface—Indicates the type of interface on wh

238 Configuring Switch Informationwww.dell.com | support.dell.com NOTE: The following relationships between the various timer values must be maintaine

Configuring Switch Information 2393 Select an interface in the Copy Parameters from field. 4 Select the interfaces to which the GARP Timers informatio

24 Hardware Descriptionwww.dell.com | support.dell.comPorts DescriptionEthernet Port DescriptionThe PowerConnect 3324 features 24 FE 10BaseT/100BaseTX

240 Configuring Switch Informationwww.dell.com | support.dell.comSpanning Tree PageThis section contains the following topics:• Defining STP Global Se

Configuring Switch Information 241Spanning Tree Global Settings PageThe Spanning Tree Global Parameters page contains the following fields: • Spanning

242 Configuring Switch Informationwww.dell.com | support.dell.com• Max Age (6-40)—Specifies the switch Maximum Age Time. The Maximum Age Time indicate

Configuring Switch Information 243The following is an example of the CLI commands: Console(config)# spanning-treeConsole(config)# spanning-tree mode r

244 Configuring Switch Informationwww.dell.com | support.dell.comRoot ID Priority 32768Address X.X.X.X.X.XCost 57Port 1/e1Hello Time 2 sec Max Age 20

Configuring Switch Information 245STP Port Settings PageThe STP Port Settings page contains the following fields: • Select a Port—Indicates the port f

246 Configuring Switch Informationwww.dell.com | support.dell.com– Learning—The port is currently in the learning mode. The port cannot forward traffi

Configuring Switch Information 247Modifying STP Port Properties:1 Open the STP Port Settings page.2 Modify the Priority, Path Cost, Default Path Cost,

248 Configuring Switch Informationwww.dell.com | support.dell.comConsole(config-if)# spanning-tree cost 35000Console(config-if)# spanning-tree port-pr

Configuring Switch Information 249STP LAG Settings PageThe STP LAG Settings page contains the following fields:• Select a LAG—Indicates the user-defin

Hardware Description 25Front Panel LEDs: 24 PortsFront Panel LEDs: 48 PortsG1 G22143658710912111413161518172019222124232143658710912111413161518172019

250 Configuring Switch Informationwww.dell.com | support.dell.com– Blocking—The LAG is currently blocked and cannot be used to forward traffic or lear

Configuring Switch Information 2513 Click Apply Changes. The STP LAG parameters are modified, and the device is updated.STP LAG Table PageDefining STP

252 Configuring Switch Informationwww.dell.com | support.dell.comSTP has the following different port states:• Listening• Learning• Blocking•Forwardin

Configuring Switch Information 253The Rapid Spanning Tree (RSTP) page contains the following fields:• Interface—Indicates the interface number on whic

254 Configuring Switch Informationwww.dell.com | support.dell.comDefining Rapid STP Parameters Using CLI CommandsThe following table summarizes the eq

Configuring Switch Information 255VLANs function at Layer 2. Since VLANs isolate traffic within the VLAN, a Layer 3 functioning router is needed to al

256 Configuring Switch Informationwww.dell.com | support.dell.com• Defining VLAN LAG Settings• Configuring GVRPDefining VLAN MembersThe VLAN Membershi

Configuring Switch Information 257VLAN Membership SectionThe VLAN Membership Section contains the following fields:• Show VLAN—Lists and displays spec

258 Configuring Switch Informationwww.dell.com | support.dell.comAdding new VLANs:1 Open the VLAN Membership page.2 Click Add. The Create New VLAN pag

Configuring Switch Information 259The following is an example of the CLI commands: Console # vlan databaseConsole (config-switch)#Console (config-swit

26 Hardware Descriptionwww.dell.com | support.dell.comPort LEDsEach port has one corresponding LED located above the port. The LEDs show either link a

260 Configuring Switch Informationwww.dell.com | support.dell.comThe VLAN Port Membership Table displays the ports and the ports states, as well as LA

Configuring Switch Information 261The following is an example of the CLI commands: Console # vlan databaseConsole (config-vlan)# vlan 1972Console (con

262 Configuring Switch Informationwww.dell.com | support.dell.comVLAN Port Settings PageThe VLAN Port Settings page contains the following fields:• Po

Configuring Switch Information 263– Admit All—Indicates that both tagged and untagged packets are accepted on the port.• Ingress Filtering—Enables Ing

264 Configuring Switch Informationwww.dell.com | support.dell.comAssigning Ports to VLAN Groups Using CLI CommandsThe following table summarizes the e

Configuring Switch Information 265VLAN LAG Setting PageThe VLAN LACP Parameters page contains the following fields:• LAG—Indicates the LAG number incl

266 Configuring Switch Informationwww.dell.com | support.dell.com• Ingress Filtering—Enables ingress filtering by the LAG. Ingress filtering discards

Configuring Switch Information 267The following is an example of the CLI commands: Console (config)# interface port channel 1 1/e8Console (config-if)#

268 Configuring Switch Informationwww.dell.com | support.dell.com• Maximum number of GVRP VLANs after Reset—Sets another value for GVRP VLANs and is u

Configuring Switch Information 269GVRP Parameters PageThe GVRP Parameters page contains the following fields:• GVRP Global Status—Enables GVRP on the

Hardware Description 27Giga Port Link Activity Status• The Mode button located next to the system LEDs is used to toggle between the two display modes

270 Configuring Switch Informationwww.dell.com | support.dell.com– Disable—Disables creating VLANs through GVRP.• GVRP Registration—Enables GVRP regis

Configuring Switch Information 271GVRP Port Parameters Table In addition to the field displayed in the GVRP Parameters page , the GVRP Port Parameters

272 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# gvrp enableConsole

Configuring Switch Information 273Aggregated links can be assigned manually or automatically by enabling the Link Aggregation Control Protocol (LACP)

274 Configuring Switch Informationwww.dell.com | support.dell.comLink Aggregation PageThis section includes the following topics:• Defining LACP Param

Configuring Switch Information 275LACP Parameters PageThe LACP Parameters page contains the following sections:• Global Parameters• Port Parameters Ta

276 Configuring Switch Informationwww.dell.com | support.dell.comGlobal ParametersThe Global Parameters section contains the following field:• LACP Sy

Configuring Switch Information 277• LACP Port Priority—Indicates the port LACP priority value. The default is 1.• LACP Timeout—Assigns an administrati

278 Configuring Switch Informationwww.dell.com | support.dell.comConfiguring LACP Parameters Using CLI CommandsThe following table summarizes the equi

Configuring Switch Information 279Defining LAG MembershipThe LAG Membership page allows network managers to assign ports to LAGs. LAGs can include up

28 Hardware Descriptionwww.dell.com | support.dell.comStacking LEDsThe stacking LEDs indicate the unit’s position in the stack. As shown in the front

280 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console# channel-group port-channel-

Configuring Switch Information 281To open the Multicast Support page: •Click Switch > Multicast Support in the Tree View. The Multicast Support pag

282 Configuring Switch Informationwww.dell.com | support.dell.comWhen IGMP snooping is globally enabled, the switching ASIC is programmed to forward a

Configuring Switch Information 283• IGMP Snooping Status—Indicates if IGMP snooping is enabled on the device. The possible field values are:– Enabled—

284 Configuring Switch Informationwww.dell.com | support.dell.comAdding Bridge Multicast Group MembersThe Bridge Multicast Group page displays the por

Configuring Switch Information 285The IGMP Port/LAG Members Table figure displays IGMP Port/LAG member status.IGMP Port/LAG Members TableThe IGMP Port

286 Configuring Switch Informationwww.dell.com | support.dell.comAssigning LAGs to receive multicast service:1 Open the Bridge Multicast page.2 Define

Configuring Switch Information 2871 0100.5e02.0203 static1/e1, 2/e219 0100.5e02.0208 static 1/e1-819 0100.5e02.0208 dynamic1/e9-11Forbidden ports fo

288 Configuring Switch Informationwww.dell.com | support.dell.com• Ports Table—Lists the port that can be added to a multicast service.• LAGs Table—Li

Configuring Switch Information 289The following is an example of the CLI commands: Console # show bridge multicast filteringFiltering: EnabledVLAN: 1P

SECTION 3Installing the PowerConnect 3324/3348 SwitchInstallation PrecautionsSite RequirementsUnpacking and InstallationCable, Port, and Pinout Inform

290 Configuring Switch Informationwww.dell.com | support.dell.comIGMP Snooping PageThe IGMP Snooping page contains the following information:• VLAN ID

Configuring Switch Information 291• Leave Time Out (1-3600000)—Specifies the amount of time in seconds after a port leave message is received before t

292 Configuring Switch Informationwww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# interface vlan 2Co

SECTION 8Viewing StatisticsViewing TablesViewing RMON InformationViewing Charts

294 Viewing Statisticswww.dell.com | support.dell.comThe Statistic pages contains device information for interface, GVRP, etherlike, RMON, and device

Viewing Statistics 295Table View PageThe Table View page contains the following links: • Viewing Utilization Summary• Viewing Counter Summary• Viewing

296 Viewing Statisticswww.dell.com | support.dell.comUtilization Summary PageThe Utilization Summary page contains the following fields: • Unit No.—In

Viewing Statistics 297Viewing Counter SummaryThe Counter Summary page contains statistics for port utilization in numeric sums as opposed to percentag

298 Viewing Statisticswww.dell.com | support.dell.com• Transmit Non-Unicast Packets—Indicates the number of transmitted non-Unicast packets from the p

Viewing Statistics 299The Interface Statistics page contains the following fields: • Interface—Specifies the interface (type and number) for which the

Contents 3Contents1 OverviewSystem Description . . . . . . . . . . . . . . . . . . . . . . . . . 12PowerConnect 3324/3348 Stacking Overview. . . . .

30 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comInstallation Precautions CAUTION: The rack or cabinet housing the switc

300 Viewing Statisticswww.dell.com | support.dell.com• Transmitted Broadcast Packets—Displays the amount of Broadcast packets transmitted from the sel

Viewing Statistics 301PortOutOctetsOutUcastPktsOutMcastPktsOutBcastPkts-------------------------------------------------1/e121845032626Alignment Error

302 Viewing Statisticswww.dell.com | support.dell.comEtherlike Statistics PageThe Etherlike Statistics page contains the following fields: • Interface

Viewing Statistics 303• Single Collision Frames—Displays the amount of Single Collisions Frames errors received on the selected interface.• Multiple C

304 Viewing Statisticswww.dell.com | support.dell.comViewing GVRP StatisticsThe GVRP Statistics page contains device statistics for GVRP. To open the

Viewing Statistics 305• Join Empty—Displays the device GVRP Join Empty statistics.• Empty—Displays the device GVRP Empty statistics.• Leave Empty—Disp

306 Viewing Statisticswww.dell.com | support.dell.comThe following is an example of the CLI commands:Console# show gvrp statisticsGVRP statistics:----

Viewing Statistics 307Viewing RMON InformationRemote Monitoring (RMON) allows network managers to view network traffic information from a remote locat

308 Viewing Statisticswww.dell.com | support.dell.comRMON Statistics Group PageThe RMON Statistics Group page contains the following information:• Int

Viewing Statistics 309• Multicast Packets Received—Indicates the amount of Multicast packets received on the interface since the counters were last cl

Installing the PowerConnect 3324/3348 Switch 31• Power—The unit is installed within 1.5 m (5 feet) of a grounded, easily accessible outlet 100-250 VAC

310 Viewing Statisticswww.dell.com | support.dell.comThe following is an example of the CLI command: Console# show rmon statistics ethernet 1/e1Port 1

Viewing Statistics 311RMON History Control PageThe RMON History Control page contains the following information: • History Entry No.—Specifies the His

312 Viewing Statisticswww.dell.com | support.dell.comAdding a History Control Entry:1 Open the RMON History Control page.2 Click Add. The Add History

Viewing Statistics 313History Control TableDeleting a History Control Table entry:1 Open the RMON History Control page.2 Select a History Control Tabl

314 Viewing Statisticswww.dell.com | support.dell.comRMON History Table NOTE: Not all fields are shown in the RMON History Table. The RMON History Tab

Viewing Statistics 315• Oversized Packets—Indicates the number of packets received that are more than 1518 octets long during the sampling session.• F

316 Viewing Statisticswww.dell.com | support.dell.comConsole (config-if)# rmon collection history 1 interval 2400Console# show rmon history 1 throughp

Viewing Statistics 317RMON Events Control PageThe RMON Events Control page contains the following fields:• Event Entry—Indicates the event.• Community

318 Viewing Statisticswww.dell.com | support.dell.comAdding a RMON Event:1 Open the RMON Events Control page.2 Click Add. The Add New RMON Event page

Viewing Statistics 319RMON Events TableDeleting multiple RMON Event entries:1 Open the RMON Events Control page.2 Select an Event Table entry in the E

32 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com6 Inspect the product for damage. Report any damage immediately. For inf

320 Viewing Statisticswww.dell.com | support.dell.com1ErrorsLogCLIJan 18 2002 23:58:172High BroadcastLog-TrapdeviceManagerJan 18 2002 23:59:48Viewing

Viewing Statistics 321Viewing RMON Events Log Using the CLI CommandsThe following table summarizes the equivalent CLI commands for viewing fields disp

322 Viewing Statisticswww.dell.com | support.dell.com• Click Statistics/RMON > RMON> Alarms in the Tree View. The RMON Alarm page opens.RMON Ala

Viewing Statistics 323• Rising/Falling Event—The mechanism that reports the alarms: LOGed or TRAPed or a combination of both. When LOG is selected, th

324 Viewing Statisticswww.dell.com | support.dell.comNew Alarm Entry3Define the New Alarm Index, Sample Variable, Sample Type, Rising Threshold, Risin

Viewing Statistics 325RMON Alarm TableDeleting an Alarm Table entry:1 Open the RMON Alarm page.2 Select an RMON Alarm in the Alarm Entry drop-down box

326 Viewing Statisticswww.dell.com | support.dell.com31.3.6.1.2.1.2.2.1.10.9CLIConsole# show rmon alarm 1Alarm 1-------OID: 1.3.6.1.2.1.2.2.1.10.1Last

Viewing Statistics 327Charts PageThe Charts page contains the following links: • Viewing Port Statistics• Viewing LAG StatisticsViewing Port Statistic

328 Viewing Statisticswww.dell.com | support.dell.comPort Statistics PageThe Port Statistics page contains the following fields: • Interface Statistic

Viewing Statistics 329Viewing Port Statistics Using the CLI CommandsThe following table summarizes the equivalent CLI commands for viewing fields disp

Installing the PowerConnect 3324/3348 Switch 33Stacking PowerConnect 3324/3348 PowerConnect 3324/3348 supports stacking up to six PowerConnect 3324/33

330 Viewing Statisticswww.dell.com | support.dell.com512 to 1023 Octets: 491 1024 to 1518 Octets: 389 Console # configureConsole (config)# clear gvrp

Viewing Statistics 331INVPROT : Invalid Protocol Id INVPLEN : Invalid PDU LengthINVATYP : Invalid Attribute Type INVALEN : Invalid Attribute Le

332 Viewing Statisticswww.dell.com | support.dell.comLAG Statistics PageThe LAG Statistics page contains the following fields: • Interface Statistics—

Viewing Statistics 333Viewing LAG Statistics Using the CLI CommandsThe following table contains the CLI commands for viewing LAG statistics. The follo

334 Viewing Statisticswww.dell.com | support.dell.com--------------------------------------------1/e118389212899878PortOutOctetsOutUcastPktsOutMcastPk

SECTION 9Configuring Quality of ServiceQuality of Service (QoS) OverviewDefining QoS Global ParametersMapping to Queues

336 Configuring Quality of Servicewww.dell.com | support.dell.comThis section provides information for defining and configuring Quality of Service (Qo

Configuring Quality of Service 337QoS includes traffic such as voice, video, and real-time traffic that can be assigned a high priority queue, while o

338 Configuring Quality of Servicewww.dell.com | support.dell.comCoS to Queue Mapping Table Default ValuesCoS mapping is enabled on a per-system basis

Configuring Quality of Service 339• Weighted Round Robin—Ensures that a single application does not dominate the forwarding capacity of PowerConnect 3

34 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comConnected StackFor more information on configuring stacks, see "Con

340 Configuring Quality of Servicewww.dell.com | support.dell.comThe QoS Global Parameters page contains links for:• Configuring Global QoS Settings•

Configuring Quality of Service 341• Trust Mode—Determines which packet fields to use for classifying packets entering the switch. When no rules are de

342 Configuring Quality of Servicewww.dell.com | support.dell.comConsole (config)# qos trust dscpDefining QoS Interface SettingsThe QoS Interface Sett

Configuring Quality of Service 343• Set Default CoS For Incoming Traffic To—Sets the default CoS tag value untagged packets. The CoS tag values are 0-

344 Configuring Quality of Servicewww.dell.com | support.dell.comQueue Setting PageThe Queue Settings page contains the following fields: • Queues—Ind

Configuring Quality of Service 345Assigning Queue Setting Using the CLI CommandsThe following table summarizes the equivalent CLI commands for configu

346 Configuring Quality of Servicewww.dell.com | support.dell.com6 - 37 - 3Mapping to QueuesThe Mapping to Queue page contains links to pages for mapp

Configuring Quality of Service 347CoS to Queue Mapping Table PageThe CoS to Queue Mapping Table page contains the following fields: • Class of Service

348 Configuring Quality of Servicewww.dell.com | support.dell.comAssigning CoS Values to Queues Using the CLI CommandsThe following table summarizes t

Configuring Quality of Service 349DSCP Mapping PageThe For the list of the DSCP default queue settings, contains the following fields: NOTE: In a sta

Installing the PowerConnect 3324/3348 Switch 35Connecting PowerConnect 3324/3348 to a Power Supply• Plug in the PowerConnect 3324/3348 to one of the p

350 Configuring Quality of Servicewww.dell.com | support.dell.comThe following is an example of the CLI commands: Console (config)# qos map dscp-queue

Configuring Quality of Service 351• Insert TCP Port—Enables defining a new TCP port.• Map to Queue—Indicates the traffic queue to which the TCP port i

352 Configuring Quality of Servicewww.dell.com | support.dell.comTCP to Queue Mapping Table Removing a TCP port mapping from the TCP to Queue Mapping

Configuring Quality of Service 353Console (config)# show qos map tcp-port-queueTcp port-queue map:Port queue----- ------6000 16001 26002 3Mapping UDP

354 Configuring Quality of Servicewww.dell.com | support.dell.com• Insert UDP Port—A new UDP port may be defined.• Map to Queue—Indicates the traffic

Configuring Quality of Service 355Assigning UDP Ports to Queues Using the CLI CommandsThe following table summarizes the equivalent CLI commands for c

356 Configuring Quality of Servicewww.dell.com | support.dell.com

SECTION 10Getting HelpTechnical AssistanceDell Enterprise Training and CertificationProblems With Your OrderProduct InformationReturning Items for War

358 Getting Helpwww.dell.com | support.dell.comTechnical AssistanceIf you need assistance with a technical problem, use Dell's extensive suite of

Getting Help 359• Anonymous file transfer protocol (FTP)ftp.dell.com/Log in as user:anonymous, and use your e-mail address as your password. • Electro

36 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comPort ConnectionsThe ports are all standard RJ45 Ethernet ports. Switchin

360 Getting Helpwww.dell.com | support.dell.comTechnical Support ServiceDell's technical support service is available 24 hours a day, 7 days a we

Getting Help 3615 Pack the equipment to be returned in the original (or equivalent) packing materials.You are responsible for paying shipping expenses

362 Getting Helpwww.dell.com | support.dell.comCountry (City)International Access Code Country CodeCity CodeDepartment Name or Service Area,Website an

Getting Help 363Belgium (Brussels)International Access Code: 00Country Code: 32City Code: 2Website: support.euro.dell.comE-mail: [email protected]

364 Getting Helpwww.dell.com | support.dell.comCayman Islands General Support1-800-805-7541Chile (Santiago)Country Code: 56City Code: 2Sales, Customer

Getting Help 365Czech Republic (Prague)International Access Code: 00Country Code: 420City Code: 2Website: support.euro.dell.comE-mail: czech_dell@dell

366 Getting Helpwww.dell.com | support.dell.comFinland (Helsinki)International Access Code: 990Country Code: 358City Code: 9Website: support.euro.dell

Getting Help 367Germany (Langen)International Access Code: 00Country Code: 49City Code: 6103Website: support.euro.dell.comE-mail: tech_support_central

368 Getting Helpwww.dell.com | support.dell.comHong KongInternational Access Code: 001Country Code: 852Website: support.ap.dell.comE-mail: ap_support@

Getting Help 369Italy (Milan)International Access Code: 00Country Code: 39City Code: 02Website: support.euro.dell.comE-mail: support.euro.dell.com/it/

Installing the PowerConnect 3324/3348 Switch 37The following figure illustrates the Gigaport Connector:GigaPort ConnectorA serial cable connects Power

370 Getting Helpwww.dell.com | support.dell.comJapan (Kawasaki)International Access Code: 001Country Code: 81City Code: 44Website: support.jp.dell.com

Getting Help 371Latin America Customer Technical Support (Austin, Texas, U.S.A.)512 728-4093Customer Service (Austin, Texas, U.S.A.)512 728-3619Fax (T

372 Getting Helpwww.dell.com | support.dell.comMexicoInternational Access Code: 00Country Code: 52Customer Technical Support001-877-384-8979or 001-877

Getting Help 373New ZealandInternational Access Code: 00Country Code: 64E-mail (New Zealand): [email protected] (Australia): au_tech_supp

374 Getting Helpwww.dell.com | support.dell.comPortugalInternational Access Code: 00Country Code: 351Website: support.euro.dell.comE-mail: support.eur

Getting Help 375Spain (Madrid)International Access Code: 00Country Code: 34City Code: 91Website: support.euro.dell.comE-mail: support.euro.dell.com/es

376 Getting Helpwww.dell.com | support.dell.comSwitzerland (Geneva)International Access Code: 00Country Code: 41City Code: 22Website: support.euro.del

Getting Help 377U.K. (Bracknell)International Access Code: 00Country Code: 44City Code: 1344Website: support.euro.dell.comCustomer Care website: suppo

378 Getting Helpwww.dell.com | support.dell.comU.S.A. (Austin, Texas)International Access Code: 011Country Code: 1Automated Order-Status Servicetoll-f

38 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comThe following figure illustrates the DB-9 connector. DB-9 Serial CableDB

Installing the PowerConnect 3324/3348 Switch 39ASCII Terminal (Serial) ConnectionThe serial port connector is a DB-9 type connector. A supplied interf

4 Contents3 Installing the PowerConnect 3324/3348 SwitchInstallation Precautions . . . . . . . . . . . . . . . . . . . . . . 30Site Requirements. .

40 Installing the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comPowerConnect 3348 Terminal Connection

SECTION 4Configuring the PowerConnect 3324/3348 SwitchConfiguration OverviewGeneral Configuration InformationTerminal Connection ConfigurationOther Co

42 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comConfiguration OverviewThis section describes the initial device configu

Configuring the PowerConnect 3324/3348 Switch 43Instructions for setting up the device and hardware are provided in the preceding sections. For a firs

44 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comSwitching Port Default SettingsThe following table describes the Port d

Configuring the PowerConnect 3324/3348 Switch 45Baud RateThe baud rates can be manually changed to any of the following values: • 2400• 4800• 9600• 19

46 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comOther Configuration RequirementsThe following is required for downloadi

Configuring the PowerConnect 3324/3348 Switch 47BOOT Software Version 1.30.11 Built 27-JAN-2003 10:06:03Processor: MPC8245 Rev 0.12, 250 MHz (Bus: 100

48 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comSTAND ALONEThe BCM5625_A1 0 initiate successfullyThe BCM5625_A1 1 initi

Configuring the PowerConnect 3324/3348 Switch 49Initial ConfigurationInitial configuration starts after the device has booted successfully. The initia

Contents 5User Name, Password, and Privilege Level . . . . . . . . . . . 51SNMP Community Strings . . . . . . . . . . . . . . . . . . . 51Advanced

50 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comGateway IP Address Activity status----------------------- -------------

Configuring the PowerConnect 3324/3348 Switch 51Default GatewayTo manage a PowerConnect 3324/3348 device from a remote network, a default gateway, whi

52 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comThe device is SNMP-compliant. It contains an SNMP agent that supports a

Configuring the PowerConnect 3324/3348 Switch 53To configure SNMP station IP address and community string(s):1 At the console prompt, type Enable. The

54 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comWhen configuring/receiving IP addresses through DHCP and BOOTP, the con

Configuring the PowerConnect 3324/3348 Switch 55console# NOTE: The device configuration does not need to be deleted to retrieve an IP address for the

56 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comTo verify the IP address, see the following display example.console>

Configuring the PowerConnect 3324/3348 Switch 57Configuring Security PasswordsThe security passwords can be configured for the following services:•Con

58 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comConfiguring an Initial Telnet PasswordTo configure an initial Telnet pa

Configuring the PowerConnect 3324/3348 Switch 59Configuring an Initial HTTP PasswordTo configure an initial HTTP password, enter the following command

6 ContentsDefining SNMP Settings . . . . . . . . . . . . . . . . . . . . . 85Connecting Devices . . . . . . . . . . . . . . . . . . . . . . . . 8

60 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comSample Configuration ProcessThe purpose of this chapter is to present t

Configuring the PowerConnect 3324/3348 Switch 61 NOTE: 9600 is the default baud rate for new device. If using 9600 baud rate does not result in viewin

62 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comBooting...------ Performing the Power-On Self Test (POST( ------UART Ch

Configuring the PowerConnect 3324/3348 Switch 63********************************************************************* Running SW Ver. 1.0.0.52 Date

64 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comJan-2000 01:01:13 %LINK-W-Down: 1/e2201-Jan-2000 01:01:13 %LINK-W-Down

Configuring the PowerConnect 3324/3348 Switch 65******************************************************************* SYSTEM RESET *******************

66 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com4 Enter the command interface ethernet at the console to enter the Devi

Configuring the PowerConnect 3324/3348 Switch 67console(config)# exitconsole# ping 50.1.1.264 bytes from 50.1.1.2: icmp_seq=1. time=0 ms64 bytes from

68 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comconsole(config)# line telnetconsole(config-line)# login authentication

Configuring the PowerConnect 3324/3348 Switch 693 Select the option to configure the internet protocol (TCP/IP) and click Properties. The Internet Pro

Contents 7Managing Logs . . . . . . . . . . . . . . . . . . . . . . . . . . 113Defining Global Log Parameters. . . . . . . . . . . . . . . . 114Dis

70 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com4 Select Use the following IP address option.5 In the Internet Protocol

Configuring the PowerConnect 3324/3348 Switch 71Once Access is granted, command usage is the same as in direct device management: 1 Under Windows clic

72 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comNotice that Device indicates (In ASCII terminal) Telnet session status:

Configuring the PowerConnect 3324/3348 Switch 732 In the browser window type the IP previously configured on the device (with or without http:// prefi

74 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com3 When the authentication window is displayed, enter the Username and p

Configuring the PowerConnect 3324/3348 Switch 75The PowerConnect 3324/3348 Interface Components Table lists the interface components with their corres

76 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com4 Select Unit 2 using the Stack ID button within 15 seconds. 5 Repeat s

Configuring the PowerConnect 3324/3348 Switch 77Startup Menu FunctionsFrom the Startup Menu, additional device configuration functions are performed.

78 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com NOTE: The <Return> or <Esc> key must be pressed within 2

Configuring the PowerConnect 3324/3348 Switch 79To erase the device configuration:1 Verify that the ASCII terminal is connected to the device.2 Connec

8 Contents7 Configuring Switch InformationConfiguring Network Security . . . . . . . . . . . . . . . . . . 190Network Security Overview . . . . . .

80 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com7 Confirm by typing Y. The following message is displayed:Erasing flash

Configuring the PowerConnect 3324/3348 Switch 81Downloading the Software Sequentially Using the CLI1 Ensure that an IP address is assigned to at least

82 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com5 Enter console# copy tftp://50.1.1.2/332448-10018.dos unit://2/image.

Configuring the PowerConnect 3324/3348 Switch 831 Ensure that an IP address is assigned to at least one port on the Master unit.2 Enter console# show

84 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.com6 Enter console# reload. The following message displays:This command wi

Configuring the PowerConnect 3324/3348 Switch 85Defining SNMP SettingsSimple Network Management Protocol (SNMP) provides a method for managing network

86 Configuring the PowerConnect 3324/3348 Switchwww.dell.com | support.dell.comConnecting DevicesAfter assigning IP addresses to the PowerConnect devi

SECTION 5Getting StartedStarting the Switch AdministratorUnderstanding the InterfaceUsing the Switch Administrator ButtonsUsing the CLIStarting the CL

88 Getting Startedwww.dell.com | support.dell.comStarting the Switch AdministratorThe Dell™ PowerConnect™ 3324/3348 Dell OpenManage™ Switch Administra

Getting Started 89PowerConnect 3324/3348 Web Management InterfaceThe PowerConnect 3324/3348 Interface Components Table lists the interface components

Contents 9Multicast Forwarding Support . . . . . . . . . . . . . . . . . . 280Defining IGMP Snooping Settings. . . . . . . . . . . . . . . 281Addin

90 Getting Startedwww.dell.com | support.dell.comThe branches in the Tree View can be expanded to view all the components under a specific feature or

Getting Started 91PowerConnect 3348 The port coloring indicates whether a specific port is currently active. Ports are reflected in the following colo

92 Getting Startedwww.dell.com | support.dell.comExample of Work Desk InformationUsing the Switch Administrator ButtonsThis section contains informati

Getting Started 93Information ButtonsThe Switch Administrator home page contains the following information buttons:Information ButtonsSupport ButtonTh

94 Getting Startedwww.dell.com | support.dell.com2 Select the area that describes the support needed. The appropriate support page displays.3 Enter a

Getting Started 95About PageDevice Management ButtonsThe Switch Administrator management buttons allow network managers to easily configure PowerConne

96 Getting Startedwww.dell.com | support.dell.comAdds ACEs to ACLs. Adds ACLs. Adds new lists. Attaches assorted lists to interfaces. Resets statistic

Getting Started 97Using the CLIThis section contains an introduction to the Command Line Interface (CLI).Command ModeThe CLI is divided into command m

98 Getting Startedwww.dell.com | support.dell.comTo list the user EXEC commands enter the command ?.The user-level prompt consists of the host name fo

Getting Started 99The exit command is used to move back from any mode to a previous level mode, for example, from Interface Configuration Mode to Glob