Dell PowerConnect W Clearpass 100 Software Guía de usuario descargar pdf (Pagina 51)

Graph

Name

Description Monitoring Procedure

To see an enlarged view, click the graph.

The enlarged view provides Last,

Minimum, Maximum, and Average

statistics for the number of clients

associated with the OAW-IAP for the last

15 minutes.

To see the exact number of clients

associated with the selected OAW-IAP at a

particular time, hover the cursor over the

graph line.

appears. This is the default view.

2. In the Access Points tab, click the OAW-IAP for

which you want to monitor the client association.

The OAW-IAP view appears.

3. Study the Clients graph. For example, the graph

shows that six clients are associated with the OAW-

IAP at 12:11 hours.

Throughput The Throughput graph shows the

throughput for the selected OAW-IAP for

the last 15 minutes.

l Outgoing traffic — Throughput for

outgoing traffic is displayed in green.

Outgoing traffic is shown about the

median line.

l Incoming traffic — Throughput for

incoming traffic is displayed in blue.

Incoming traffic is shown below the

median line.

To see an enlarged view, click the graph.

l The enlarged view provides Last,

Minimum, Maximum, and Average

statistics for the incoming and outgoing

traffic throughput of the OAW-IAP for

the last 15 minutes.

To see the exact throughput of the selected

OAW-IAP at a particular time, hover the

cursor over the graph line.

To check the throughput of the selected OAW-IAP for

the last 15 minutes,

1. Log in to the Instant UI. The Virtual Controller view

appears. This is the default view.

2. In the Access Points tab, click the OAW-IAP for

which you want to monitor the throughput. The

OAW-IAP view appears.

3. Study the Throughput graph. For example, the

graph shows 44.03 Kbps incoming traffic

throughput at 12:08 hours.

Table 9:

Access Point View — Usage Trends and Monitoring Procedures

The following table describes the RF trends graphs available in the client view:

Graph

Name

Description Monitoring Procedure

Signal The Signal graph shows the signal

strength of the client for the last 15 minutes.

It is measured in decibels.

To see an enlarged view, click the graph.

The enlarged view provides Last,

Minimum, Maximum, and Average signal

statistics of the client for the last 15

minutes.

To see the exact signal strength at a

particular time, move the cursor over the

graph line.

To monitor the signal strength of the selected client for

the last 15 minutes,

1. Log in to the Instant UI. The Virtual Controller view

appears. This is the default view.

2. In the Clients tab, click the IP address of the client

for which you want to monitor the signal strength.

The client view appears.

3. Study the Signal graph in the RF Trends pane. For

example, the graph shows that signal strength for

the client is 54.0 dB at 12:23 hours.

Frames The Frames Graph shows the In and Out

frame rate per second of the client for the

last 15 minutes. It also shows data for the

Retry In and Retry Out frames.

l Outgoing frames — Outgoing frame

To monitor the In and Out frame rate per second and

retry frames for the In and Out traffic, for the last 15

minutes,

1. Log in to the Instant UI. The Virtual Controller view

appears. This is the default view.

Table 10:

Client View — RF Trends Graphs and Monitoring Procedures

AOS-W Instant 6.2.1.0-3.3| User Guide AOS-W Instant User Interface | 51

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 295 296

Dell PowerConnect W Clearpass 100 Software Guía de usuario Pagina 51

Comentarios a estos manuales

Dell PowerConnect W Clearpass 100 Software Guía de usuario Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Software Dell PowerConnect W Clearpass 100 Software