Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) El manual del propietario Pagina 53
- Pagina / 81
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5. Remove the system battery.
a. Support the battery connector by pressing down firmly on the positive side of the connector.
b. While supporting the battery connector, press the battery toward the positive side of the connector and pry it up out of the securing tabs at the
negative side of the connector.
Figure 3-21. Replacing the System Battery
6. Install the new system battery.
a. Support the battery connector by pressing down firmly on the positive side of the connector.
b. Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.
c. Press the battery straight down into the connector until it snaps into place.
7. If you removed an expansion card in step 3, replace the card now. See Installing an Expansion Card.
8. Close the system. See Opening and Closing the System.
9. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.
10. Enter the System Setup program to confirm that the battery is operating properly. See Using the System Setup Program.
11. Enter the correct time and date in the System Setup program's Time and Date fields.
12. Exit the System Setup program.
13. To test the newly installed battery, turn off the system and disconnect it from the electrical outlet for at least an hour.
14. After an hour, reconnect the system to its electrical outlet and turn it on.
15. Enter the System Setup program and if the time and date are still incorrect, see Getting Help for instructions on obtaining technical assistance.
Control Panel Assembly (Service-Only Procedure)
Removing the Control Panel
1. If applicable, remove the bezel. See Removing and Replacing the Front Bezel.
2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
3. Open the system. See Opening and Closing the System.
4. Remove the SAS controller daughter card. See Removing a SAS RAID Controller Daughter Card.
5. Disconnect the control panel cable at the back of the control panel board. See Figure3-22.
1
positive side of battery
connector
2
system
battery
3
negative side of battery
connector
NOTICE: To avoid damage to the battery connector, you must firmly support the connector while installing or removing a battery.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See
your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against
electrostatic discharge.
- About Your System 2
- Hard-Drive Indicator Codes 3
- Connecting External Devices 4
- Power Indicator Codes 5
- NIC Indicator Codes 5
- LCD Status Messages 6
- Removing LCD Status Messages 8
- System Messages 9
- Warning Messages 11
- Diagnostics Messages 11
- Alert Messages 11
- Getting Help 14
- Problems With Your Order 15
- Product Information 15
- Before You Call 16
- Contacting Dell 16
- Glossary 26
- Recommended Tools 31
- Inside the System 31
- Opening the System 33
- Cooling Fan Modules 34
- Cooling Shrouds 35
- Power Supplies 36
- Replacing a Power Supply 37
- RAID Battery 38
- Expansion Cards 39
- System Memory 40
- Memory Sparing Support 41
- Memory Mirroring Support 41
- Installing Memory Modules 41
- Removing Memory Modules 42
- Processors 43
- Installing a Processor 44
- RAC Card 45
- Optical Drive 46
- Hard Drives 47
- Expansion-Card Riser 49
- Backplane Board 50
- Sideplane Board 51
- System Battery 52
- Removing the Control Panel 53
- Installing the Control Panel 54
- Removing the System Board 55
- Installing the System Board 56
- Jumpers and Connectors 58
- System Board Connectors 59
- System Setup Options 62
- CPU Information Screen 64
- Integrated Devices Screen 64
- System Security Screen 64
- Exit Screen 65
- Using the System Password 65
- Using the Setup Password 67
- BMC Setup Module Options 68
- Start-Up Routine 69
- Checking the Equipment 69
- Troubleshooting the Keyboard 70
- Problem 71
- Troubleshooting a NIC 72
- Troubleshooting a Fan 75
Relacionado con productos y manuales para Servidores Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950)
Servidores Dell POWEREDGETM EMS01 Manual de usuario
(112 paginas)
(112 paginas)
Servidores Dell Force10 S55T Manual de inicio rápido
(28 paginas)
(28 paginas)
Servidores Dell PowerEdge R720 El manual del propietario
(163 paginas)
(163 paginas)
Servidores Dell Vizioncore Guía de usuario
(13 paginas)
(13 paginas)
Servidores Dell PowerEdge R415 Guía de inicio rápido
(52 paginas)
(52 paginas)
Servidores Dell 58260075 Ficha de datos
(1 paginas)
(1 paginas)
Servidores Dell 58259908 Ficha de datos
(1 paginas)
(1 paginas)
Servidores Dell POWEREDGE R515 Manual de instalación
(58 paginas)
(58 paginas)
Servidores Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) Guía de usuario
(38 paginas)
(38 paginas)
Servidores Dell PowerEdge systems 6300 Manual de usuario
(143 paginas)
(143 paginas)
Servidores Dell PowerVault DL2100 Manual de usuario
(200 paginas)
(200 paginas)
Servidores Dell OpenManage Server Administrator Managed Node for Fluid Cache for DAS Notas
(18 paginas)
(18 paginas)
Servidores Dell PowerEdge M915 Guía de inicio rápido
(92 paginas)
(92 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales